src/include/dec_5100.h

/*  gxemul: $Id: dec_5100.h,v 1.3 2005/03/05 12:34:02 debug Exp $  */
#ifndef DEC_5100_H
#define DEC_5100_H

/*      $NetBSD: kn230.h,v 1.2 1999/03/25 01:17:52 simonb Exp $ */

/*
 * Copyright (c) 1997,1998 Jonathan Stone.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *      This product includes software developed by Jonathan Stone for
 *      the NetBSD Project.
 * 4. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 */


/*
 * Physical addresses of baseboard devices and registers on the
 * the DECstation 5100 motherboard (also known as the kn230).
 *
 * The only options on the kn230 are two slots for daughterboards.
 * Each slot can contain an extra four-port dc708x DZ11 clone chip.
 * Most baseborad chips are the same hardware and at the same
 * address as  the DECstation 3100 (kn01), except:
 *
 *      The kn230 has more devices than the 3100, so instead
 *      of hardwiring each device to a CPU interrupt line,
 *      the kn230 provides an interrupt-request  register (ICSR).
 *      Devices are mapped onto  CPU interrupt lines as below:
 *          hardint 5:  fpu
 *          hardint 4:  reset switch
 *          hardint 3:  memory error (write to nonexistent memory)
 *          hardint 2:  clock
 *          hardint 1:  sii, lance
 *          hardint 0:  baseboard DZ, I/O option cards
 *
 *      the ICSR only indicates which devices are requesting interrupts.
 *      there is no interrupt mask register.
 *
 *      There is no framebuffer, pcc (cursor), colormap or vdac on a 5100.
 */

#define KN230_SYS_LANCE         0x18000000      /* Lance chip */
#define KN230_SYS_LANCE_B_START 0x19000000      /* 64 Kb Lance Buffer */
#define KN230_SYS_LANCE_B_END   0x19010000

#define KN230_SYS_SII           0x1a000000      /* scsi SII chip */
#define KN230_SYS_SII_B_START   0x1b000000      /* 128 Kb SCSI buffer */
#define KN230_SYS_SII_B_END     0x1b020000

#define KN230_SYS_DZ0           0x1c000000      /* baseboard DZ serial chip */

#define KN230_SYS_CLOCK         0x1d000000      /* mc146818 rtc chip */

#define KN230_SYS_ICSR          0x1e000000      /* System control register */

/*
 * Interrupt-request bitmasks in the low-order 16 bits of the CSR.
 * If a bit is set, the corresponding device has an  interrupt condition.
 * There is no equivalent per-device interrupt masking register.
 * (note: these were LED control bits in the kn01).
 */
#define KN230_CSR_INTR_RESET    0x00004000      /* reset button */
#define KN230_CSR_INTR_WMERR    0x00002000      /* badaddr() or write error */
#define KN230_CSR_INTR_LANCE    0x00001000      /* lance interrupt */
#define KN230_CSR_INTR_SII      0x00000800      /* scsi interrupt */
#define KN230_CSR_INTR_OPT1     0x00000400      /* second option DZ */
#define KN230_CSR_INTR_OPT0     0x00000200      /* first option DZ */
#define KN230_CSR_INTR_DZ0      0x00000100      /* baseboard DZ */

/*
 * kn230 LED control  register.
 * Writing a 1 bit to any bit turns off the corresponding LED.
 * low bits are or'ed to control registers which have side effects.
 *
 * This is sort of like the 3100 CSR only at a different address, and
 * with the same external-logic hack as the 5000/200 to enable 38.4
 * baud mode on the baseboard DZ chip.
 */
#define KN230_SYS_CTL_LED       0x14000000      /* LED register */
#define KN230_LED7              0x00008000      /* no side effect */
#define KN230_LED6              0x00004000      /* no side effect */
#define KN230_LED5              0x00002000      /* no side effect */
#define KN230_LED4              0x00001000      /* no side effect */

#define KN230_LED3              0x00000800      /* Turns off led 3.
                                                 * Also disables main memory.
                                                 * enables writes to EEPROM.
                                                 */

#define KN230_LED2              0x00000400      /* Turns off led 2.
                                                 * 0:  forces DZ to run at
                                                 * 38.4  when 19.2 is selected
                                                 * 1:  is 19.2 means 19.2.
                                                 */

#define KN230_LED1              0x00000200      /* read-only
                                                 *  0:  8M memory in bank 1
                                                 *  1: 32M in bank1
                                                 */
#define KN230_LED0              0x00000100

/*
 * Option slot addresses.
 * dc7084 registers appear here, if present.
 */
#define KN230_SYS_DZ1           0x15000000      /* DZ1 Control and status */
#define KN230_SYS_DZ2           0x15200000      /* DZ2 Control and status */

/*
 * Write error address.
 * Same address as the KN01_SYS_MERR, but with a presence bit for a
 * PrestoServe option and a secure console-mode the low-order bits.
 */
#define KN230_SYS_WEAR          0x17000000      /* Write-error address reg */
#define KN230_WEAR_OPTIONMASK   0x00000001      /* 1 if no card present */
#define KN230_WEAR_OPTION_FALSE KN230_WEAR_OPTIONMASK
#define KN230_WEAR_OPTION_TRUE  0

#define KN230_WEAR_SECUREMASK   0x00000002      /* "1": system is insecure */
#define KN230_WEAR_INSECURE     KN230_WEAR_SECUREMASK
#define KN230_WEAR_SECURE       0

/*
 * various leftover stuff....
 */

/*
 *  Option ID register. Indicates whether options are present.
 */
#define KN230_SYS_OID           0x1f00020c      /* option slot ID register */
#define KN230_OID_MASK          0x000000ff      /* ID number mask */
#define KN230_ERRCNT_MASK       0x0000ff00      /* hardware failure count */


#define KN230_SYS_PASSWD        0x1f000244      /* password location */

/*
 * NVRAM state defintions.
 * Used under Ultrix for  PrestoServe.
 */
#define KN230_SYS_NVRAM_DIAG    0x1f000300      /* NVRAM diagnostic register */
#define KN230_NVRAM_PRESENT     0x00000001
#define KN230_NVRAM_TESTFAIL_RO 0x00000002
#define KN230_NVRAM_TESTFAIL_RW 0x00000004
#define KN230_NVRAM_FAILURE     0x00000008      /* ran out of power anyway? */
#define KN230_NVRAM_SIZEMASK    0x000000f0

#define KN230_SYS_NVRAM_ADDR    0x1f000304       /* holds addr of NVRAM bank */
/*
 * NVRAM has separete control and status registers for each of
 * the two motherboard SIMM banks (even and odd),
 * located at offsets from the value at value at SYS_NVRAM_ADDR.
 */
# define KN230_SYS_NVRAM_EVENBNK_STATUS_OFFSET  (0x200000)
# define KN230_SYS_NVRAM_ODDBNK_STATUS_OFFSET   (0x200000 +4)
# define KN230_SYS_NVRAM_EVENBNK_CONTROL_OFFSET (-0x200000)
# define KN230_SYS_NVRAM_ODDNK_STATUS_OFFSET    (-0x200000+4)

/* flags in nvram per-bank status register */
#define KN230_NVRAM_BATFAIL     0x00000001       /* battery failure */
#define KN230_NVRAM_BATKILL     0x00000002       /* battery kill */
/*
 * To enable the battery,  write 0x00  to each nvram control reg.
 * To disable the battery, write the sequence
 *    0x01, 0x01,  0x00, 0x00,  0x01
 * to both per-bank control registers (do banks in parallel, not in sequence).
 */

#endif  /*  DEC_5100_H  */

1	dpavlin	4	/* gxemul: $Id: dec_5100.h,v 1.3 2005/03/05 12:34:02 debug Exp $ */
2			#ifndef DEC_5100_H
3			#define DEC_5100_H
4
5			/* $NetBSD: kn230.h,v 1.2 1999/03/25 01:17:52 simonb Exp $ */
6
7			/*
8			* Copyright (c) 1997,1998 Jonathan Stone.
9			* All rights reserved.
10			*
11			* Redistribution and use in source and binary forms, with or without
12			* modification, are permitted provided that the following conditions
13			* are met:
14			* 1. Redistributions of source code must retain the above copyright
15			* notice, this list of conditions and the following disclaimer.
16			* 2. Redistributions in binary form must reproduce the above copyright
17			* notice, this list of conditions and the following disclaimer in the
18			* documentation and/or other materials provided with the distribution.
19			* 3. All advertising materials mentioning features or use of this software
20			* must display the following acknowledgement:
21			* This product includes software developed by Jonathan Stone for
22			* the NetBSD Project.
23			* 4. The name of the author may not be used to endorse or promote products
24			* derived from this software without specific prior written permission.
25			*
26			* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND
27			* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
28			* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
29			* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE
30			* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
31			* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
32			* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
33			* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
34			* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
35			* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
36			* SUCH DAMAGE.
37			*/
38
39
40			/*
41			* Physical addresses of baseboard devices and registers on the
42			* the DECstation 5100 motherboard (also known as the kn230).
43			*
44			* The only options on the kn230 are two slots for daughterboards.
45			* Each slot can contain an extra four-port dc708x DZ11 clone chip.
46			* Most baseborad chips are the same hardware and at the same
47			* address as the DECstation 3100 (kn01), except:
48			*
49			* The kn230 has more devices than the 3100, so instead
50			* of hardwiring each device to a CPU interrupt line,
51			* the kn230 provides an interrupt-request register (ICSR).
52			* Devices are mapped onto CPU interrupt lines as below:
53			* hardint 5: fpu
54			* hardint 4: reset switch
55			* hardint 3: memory error (write to nonexistent memory)
56			* hardint 2: clock
57			* hardint 1: sii, lance
58			* hardint 0: baseboard DZ, I/O option cards
59			*
60			* the ICSR only indicates which devices are requesting interrupts.
61			* there is no interrupt mask register.
62			*
63			* There is no framebuffer, pcc (cursor), colormap or vdac on a 5100.
64			*/
65
66			#define KN230_SYS_LANCE 0x18000000 /* Lance chip */
67			#define KN230_SYS_LANCE_B_START 0x19000000 /* 64 Kb Lance Buffer */
68			#define KN230_SYS_LANCE_B_END 0x19010000
69
70			#define KN230_SYS_SII 0x1a000000 /* scsi SII chip */
71			#define KN230_SYS_SII_B_START 0x1b000000 /* 128 Kb SCSI buffer */
72			#define KN230_SYS_SII_B_END 0x1b020000
73
74			#define KN230_SYS_DZ0 0x1c000000 /* baseboard DZ serial chip */
75
76			#define KN230_SYS_CLOCK 0x1d000000 /* mc146818 rtc chip */
77
78			#define KN230_SYS_ICSR 0x1e000000 /* System control register */
79
80			/*
81			* Interrupt-request bitmasks in the low-order 16 bits of the CSR.
82			* If a bit is set, the corresponding device has an interrupt condition.
83			* There is no equivalent per-device interrupt masking register.
84			* (note: these were LED control bits in the kn01).
85			*/
86			#define KN230_CSR_INTR_RESET 0x00004000 /* reset button */
87			#define KN230_CSR_INTR_WMERR 0x00002000 /* badaddr() or write error */
88			#define KN230_CSR_INTR_LANCE 0x00001000 /* lance interrupt */
89			#define KN230_CSR_INTR_SII 0x00000800 /* scsi interrupt */
90			#define KN230_CSR_INTR_OPT1 0x00000400 /* second option DZ */
91			#define KN230_CSR_INTR_OPT0 0x00000200 /* first option DZ */
92			#define KN230_CSR_INTR_DZ0 0x00000100 /* baseboard DZ */
93
94			/*
95			* kn230 LED control register.
96			* Writing a 1 bit to any bit turns off the corresponding LED.
97			* low bits are or'ed to control registers which have side effects.
98			*
99			* This is sort of like the 3100 CSR only at a different address, and
100			* with the same external-logic hack as the 5000/200 to enable 38.4
101			* baud mode on the baseboard DZ chip.
102			*/
103			#define KN230_SYS_CTL_LED 0x14000000 /* LED register */
104			#define KN230_LED7 0x00008000 /* no side effect */
105			#define KN230_LED6 0x00004000 /* no side effect */
106			#define KN230_LED5 0x00002000 /* no side effect */
107			#define KN230_LED4 0x00001000 /* no side effect */
108
109			#define KN230_LED3 0x00000800 /* Turns off led 3.
110			* Also disables main memory.
111			* enables writes to EEPROM.
112			*/
113
114			#define KN230_LED2 0x00000400 /* Turns off led 2.
115			* 0: forces DZ to run at
116			* 38.4 when 19.2 is selected
117			* 1: is 19.2 means 19.2.
118			*/
119
120			#define KN230_LED1 0x00000200 /* read-only
121			* 0: 8M memory in bank 1
122			* 1: 32M in bank1
123			*/
124			#define KN230_LED0 0x00000100
125
126			/*
127			* Option slot addresses.
128			* dc7084 registers appear here, if present.
129			*/
130			#define KN230_SYS_DZ1 0x15000000 /* DZ1 Control and status */
131			#define KN230_SYS_DZ2 0x15200000 /* DZ2 Control and status */
132
133			/*
134			* Write error address.
135			* Same address as the KN01_SYS_MERR, but with a presence bit for a
136			* PrestoServe option and a secure console-mode the low-order bits.
137			*/
138			#define KN230_SYS_WEAR 0x17000000 /* Write-error address reg */
139			#define KN230_WEAR_OPTIONMASK 0x00000001 /* 1 if no card present */
140			#define KN230_WEAR_OPTION_FALSE KN230_WEAR_OPTIONMASK
141			#define KN230_WEAR_OPTION_TRUE 0
142
143			#define KN230_WEAR_SECUREMASK 0x00000002 /* "1": system is insecure */
144			#define KN230_WEAR_INSECURE KN230_WEAR_SECUREMASK
145			#define KN230_WEAR_SECURE 0
146
147			/*
148			* various leftover stuff....
149			*/
150
151			/*
152			* Option ID register. Indicates whether options are present.
153			*/
154			#define KN230_SYS_OID 0x1f00020c /* option slot ID register */
155			#define KN230_OID_MASK 0x000000ff /* ID number mask */
156			#define KN230_ERRCNT_MASK 0x0000ff00 /* hardware failure count */
157
158
159			#define KN230_SYS_PASSWD 0x1f000244 /* password location */
160
161			/*
162			* NVRAM state defintions.
163			* Used under Ultrix for PrestoServe.
164			*/
165			#define KN230_SYS_NVRAM_DIAG 0x1f000300 /* NVRAM diagnostic register */
166			#define KN230_NVRAM_PRESENT 0x00000001
167			#define KN230_NVRAM_TESTFAIL_RO 0x00000002
168			#define KN230_NVRAM_TESTFAIL_RW 0x00000004
169			#define KN230_NVRAM_FAILURE 0x00000008 /* ran out of power anyway? */
170			#define KN230_NVRAM_SIZEMASK 0x000000f0
171
172			#define KN230_SYS_NVRAM_ADDR 0x1f000304 /* holds addr of NVRAM bank */
173			/*
174			* NVRAM has separete control and status registers for each of
175			* the two motherboard SIMM banks (even and odd),
176			* located at offsets from the value at value at SYS_NVRAM_ADDR.
177			*/
178			# define KN230_SYS_NVRAM_EVENBNK_STATUS_OFFSET (0x200000)
179			# define KN230_SYS_NVRAM_ODDBNK_STATUS_OFFSET (0x200000 +4)
180			# define KN230_SYS_NVRAM_EVENBNK_CONTROL_OFFSET (-0x200000)
181			# define KN230_SYS_NVRAM_ODDNK_STATUS_OFFSET (-0x200000+4)
182
183			/* flags in nvram per-bank status register */
184			#define KN230_NVRAM_BATFAIL 0x00000001 /* battery failure */
185			#define KN230_NVRAM_BATKILL 0x00000002 /* battery kill */
186			/*
187			* To enable the battery, write 0x00 to each nvram control reg.
188			* To disable the battery, write the sequence
189			* 0x01, 0x01, 0x00, 0x00, 0x01
190			* to both per-bank control registers (do banks in parallel, not in sequence).
191			*/
192
193			#endif /* DEC_5100_H */
194