1 |
dpavlin |
1 |
#============================================================= -*-perl-*- |
2 |
|
|
# |
3 |
|
|
# Configuration file for BackupPC. |
4 |
|
|
# |
5 |
|
|
# DESCRIPTION |
6 |
|
|
# |
7 |
|
|
# This is the main configuration file for BackupPC. |
8 |
|
|
# |
9 |
|
|
# This file must be valid perl source, so make sure the punctuation, |
10 |
|
|
# quotes, and other syntax are valid. |
11 |
|
|
# |
12 |
|
|
# This file is read by BackupPC at startup, when a HUP (-1) signal |
13 |
|
|
# is sent to BackupPC and also at each wakeup time whenever the |
14 |
|
|
# modification time of this file changes. |
15 |
|
|
# |
16 |
|
|
# The configuration parameters are divided into four general groups. |
17 |
|
|
# The first group (general server configuration) provides general |
18 |
|
|
# configuration for BackupPC. The next two groups describe what |
19 |
|
|
# to backup, when to do it, and how long to keep it. The fourth |
20 |
|
|
# group are settings for the CGI http interface. |
21 |
|
|
# |
22 |
|
|
# Configuration settings can also be specified on a per-PC basis. |
23 |
|
|
# Simply put the relevant settings in a config.pl file in the |
24 |
|
|
# PC's backup directory (ie: in __TOPDIR__/pc/hostName). |
25 |
|
|
# All configuration settings in the second, third and fourth |
26 |
|
|
# groups can be overridden by the per-PC config.pl file. |
27 |
|
|
# |
28 |
|
|
# AUTHOR |
29 |
|
|
# Craig Barratt <cbarratt@users.sourceforge.net> |
30 |
|
|
# |
31 |
|
|
# COPYRIGHT |
32 |
|
|
# Copyright (C) 2001-2003 Craig Barratt |
33 |
|
|
# |
34 |
|
|
# See http://backuppc.sourceforge.net. |
35 |
|
|
# |
36 |
|
|
#======================================================================== |
37 |
|
|
|
38 |
|
|
########################################################################### |
39 |
|
|
# General server configuration |
40 |
|
|
########################################################################### |
41 |
|
|
# |
42 |
|
|
# Host name on which the BackupPC server is running. |
43 |
|
|
# |
44 |
|
|
$Conf{ServerHost} = ''; |
45 |
|
|
|
46 |
|
|
# |
47 |
|
|
# TCP port number on which the BackupPC server listens for and accepts |
48 |
|
|
# connections. Normally this should be disabled (set to -1). The TCP |
49 |
|
|
# port is only needed if apache runs on a different machine from BackupPC. |
50 |
|
|
# In that case, set this to any spare port number over 1024 (eg: 2359). |
51 |
|
|
# If you enable the TCP port, make sure you set $Conf{ServerMesgSecret} |
52 |
|
|
# too! |
53 |
|
|
# |
54 |
|
|
$Conf{ServerPort} = -1; |
55 |
|
|
|
56 |
|
|
# |
57 |
|
|
# Shared secret to make the TCP port secure. Set this to a hard to guess |
58 |
|
|
# string if you enable the TCP port (ie: $Conf{ServerPort} > 0). |
59 |
|
|
# |
60 |
|
|
# To avoid possible attacks via the TCP socket interface, every client |
61 |
|
|
# message is protected by an MD5 digest. The MD5 digest includes four |
62 |
|
|
# items: |
63 |
|
|
# - a seed that is sent to the client when the connection opens |
64 |
|
|
# - a sequence number that increments for each message |
65 |
|
|
# - a shared secret that is stored in $Conf{ServerMesgSecret} |
66 |
|
|
# - the message itself. |
67 |
|
|
# |
68 |
|
|
# The message is sent in plain text preceded by the MD5 digest. A |
69 |
|
|
# snooper can see the plain-text seed sent by BackupPC and plain-text |
70 |
|
|
# message from the client, but cannot construct a valid MD5 digest since |
71 |
|
|
# the secret $Conf{ServerMesgSecret} is unknown. A replay attack is |
72 |
|
|
# not possible since the seed changes on a per-connection and |
73 |
|
|
# per-message basis. |
74 |
|
|
# |
75 |
|
|
$Conf{ServerMesgSecret} = ''; |
76 |
|
|
|
77 |
|
|
# |
78 |
|
|
# PATH setting for BackupPC. An explicit value is necessary |
79 |
|
|
# for taint mode. Value shouldn't matter too much since |
80 |
|
|
# all execs use explicit paths. However, taint mode in perl |
81 |
|
|
# will complain if this directory is world writable. |
82 |
|
|
# |
83 |
|
|
$Conf{MyPath} = '/bin'; |
84 |
|
|
|
85 |
|
|
# |
86 |
|
|
# Permission mask for directories and files created by BackupPC. |
87 |
|
|
# Default value prevents any access from group other, and prevents |
88 |
|
|
# group write. |
89 |
|
|
# |
90 |
|
|
$Conf{UmaskMode} = 027; |
91 |
|
|
|
92 |
|
|
# |
93 |
|
|
# Times at which we wake up, check all the PCs, and schedule necessary |
94 |
|
|
# backups. Times are measured in hours since midnight. Can be |
95 |
|
|
# fractional if necessary (eg: 4.25 means 4:15am). |
96 |
|
|
# |
97 |
|
|
# If the hosts you are backing up are always connected to the network |
98 |
|
|
# you might have only one or two wakeups each night. This will keep |
99 |
|
|
# the backup activity after hours. On the other hand, if you are backing |
100 |
|
|
# up laptops that are only intermittently connected to the network you |
101 |
|
|
# will want to have frequent wakeups (eg: hourly) to maximized the chance |
102 |
|
|
# that each laptop is backed up. |
103 |
|
|
# |
104 |
|
|
# Examples: |
105 |
|
|
# $Conf{WakeupSchedule} = [22.5]; # once per day at 10:30 pm. |
106 |
|
|
# $Conf{WakeupSchedule} = [1..23]; # every hour except midnight |
107 |
|
|
# $Conf{WakeupSchedule} = [2,4,6,8,10,12,14,16,18,20,22]; # every 2 hours |
108 |
|
|
# |
109 |
|
|
# The default value is every hour except midnight. |
110 |
|
|
# |
111 |
|
|
# The first entry of $Conf{WakeupSchedule} is when BackupPC_nightly |
112 |
|
|
# is run. No other backups can run while BackupPC_nightly is |
113 |
|
|
# running. You might want to re-arrange the entries in |
114 |
|
|
# $Conf{WakeupSchedule} (they don't have to be ascending) so that |
115 |
|
|
# the first entry is when you want BackupPC_nightly to run |
116 |
|
|
# (eg: when you don't expect a lot of regular backups to run). |
117 |
|
|
# |
118 |
|
|
$Conf{WakeupSchedule} = [1..23]; |
119 |
|
|
|
120 |
|
|
# |
121 |
|
|
# Maximum number of simultaneous backups to run. If there |
122 |
|
|
# are no user backup requests then this is the maximum number |
123 |
|
|
# of simultaneous backups. |
124 |
|
|
# |
125 |
|
|
$Conf{MaxBackups} = 4; |
126 |
|
|
|
127 |
|
|
# |
128 |
|
|
# Additional number of simultaneous backups that users can run. |
129 |
|
|
# As many as $Conf{MaxBackups} + $Conf{MaxUserBackups} requests can |
130 |
|
|
# run at the same time. |
131 |
|
|
# |
132 |
|
|
$Conf{MaxUserBackups} = 4; |
133 |
|
|
|
134 |
|
|
# |
135 |
|
|
# Maximum number of pending link commands. New backups will only be |
136 |
|
|
# started if there are no more than $Conf{MaxPendingCmds} plus |
137 |
|
|
# $Conf{MaxBackups} number of pending link commands, plus running jobs. |
138 |
|
|
# This limit is to make sure BackupPC doesn't fall too far behind in |
139 |
|
|
# running BackupPC_link commands. |
140 |
|
|
# |
141 |
|
|
$Conf{MaxPendingCmds} = 10; |
142 |
|
|
|
143 |
|
|
# |
144 |
|
|
# How many BackupPC_nightly processes to run in parallel. |
145 |
|
|
# |
146 |
|
|
# Each night, at the first wakeup listed in $Conf{WakeupSchedule}, |
147 |
|
|
# BackupPC_nightly is run. Its job is to remove unneeded files |
148 |
|
|
# in the pool, ie: files that only have one link. To avoid race |
149 |
|
|
# conditions, BackupPC_nightly runs only when there are no backups |
150 |
|
|
# running, and no backups will start while it runs. |
151 |
|
|
# |
152 |
|
|
# So to reduce the elapsed time, you might want to increase this |
153 |
|
|
# setting to run several BackupPC_nightly processes in parallel |
154 |
|
|
# (eg: 4, or even 8). |
155 |
|
|
# |
156 |
|
|
$Conf{MaxBackupPCNightlyJobs} = 2; |
157 |
|
|
|
158 |
|
|
# |
159 |
|
|
# How many days (runs) it takes BackupPC_nightly to traverse the |
160 |
|
|
# entire pool. Normally this is 1, which means every night it runs, |
161 |
|
|
# it does traverse the entire pool removing unused pool files. |
162 |
|
|
# |
163 |
|
|
# Other valid values are 2, 4, 8, 16. This causes BackupPC_nightly to |
164 |
|
|
# traverse 1/2, 1/4, 1/8 or 1/16th of the pool each night, meaning it |
165 |
|
|
# takes 2, 4, 8 or 16 days to completely traverse the pool. The |
166 |
|
|
# advantage is that each night the running time of BackupPC_nightly |
167 |
|
|
# is reduced roughly in proportion, since the total job is split |
168 |
|
|
# over multiple days. The disadvantage is that unused pool files |
169 |
|
|
# take longer to get deleted, which will slightly increase disk |
170 |
|
|
# usage. |
171 |
|
|
# |
172 |
|
|
# Note that even when $Conf{BackupPCNightlyPeriod} > 1, BackupPC_nightly |
173 |
|
|
# still runs every night. It just does less work each time it runs. |
174 |
|
|
# |
175 |
|
|
# Examples: |
176 |
|
|
# |
177 |
|
|
# $Conf{BackupPCNightlyPeriod} = 1; # entire pool is checked every night |
178 |
|
|
# |
179 |
|
|
# $Conf{BackupPCNightlyPeriod} = 2; # two days to complete pool check |
180 |
|
|
# # (different half each night) |
181 |
|
|
# |
182 |
|
|
# $Conf{BackupPCNightlyPeriod} = 4; # four days to complete pool check |
183 |
|
|
# # (different quarter each night) |
184 |
|
|
# |
185 |
|
|
$Conf{BackupPCNightlyPeriod} = 1; |
186 |
|
|
|
187 |
|
|
# |
188 |
|
|
# Maximum number of log files we keep around in log directory. |
189 |
|
|
# These files are aged nightly. A setting of 14 means the log |
190 |
|
|
# directory will contain about 2 weeks of old log files, in |
191 |
|
|
# particular at most the files LOG, LOG.0, LOG.1, ... LOG.13 |
192 |
|
|
# (except today's LOG, these files will have a .z extension if |
193 |
|
|
# compression is on). |
194 |
|
|
# |
195 |
|
|
# If you decrease this number after BackupPC has been running for a |
196 |
|
|
# while you will have to manually remove the older log files. |
197 |
|
|
# |
198 |
|
|
$Conf{MaxOldLogFiles} = 14; |
199 |
|
|
|
200 |
|
|
# |
201 |
|
|
# Full path to the df command. Security caution: normal users |
202 |
|
|
# should not allowed to write to this file or directory. |
203 |
|
|
# |
204 |
|
|
$Conf{DfPath} = '/bin/df'; |
205 |
|
|
|
206 |
|
|
# |
207 |
|
|
# Command to run df. The following variables are substituted at run-time: |
208 |
|
|
# |
209 |
|
|
# $dfPath path to df ($Conf{DfPath}) |
210 |
|
|
# $topDir top-level BackupPC data directory |
211 |
|
|
# |
212 |
|
|
$Conf{DfCmd} = '$dfPath $topDir'; |
213 |
|
|
|
214 |
|
|
# |
215 |
|
|
# Full path to various commands for archiving |
216 |
|
|
# |
217 |
|
|
|
218 |
|
|
$Conf{SplitPath} = '/usr/bin/split'; |
219 |
|
|
$Conf{ParPath} = '/usr/bin/par2'; |
220 |
|
|
$Conf{CatPath} = '/bin/cat'; |
221 |
|
|
$Conf{GzipPath} = '/bin/gzip'; |
222 |
|
|
$Conf{Bzip2Path} = '/usr/bin/bzip2'; |
223 |
|
|
|
224 |
|
|
# |
225 |
|
|
# Maximum threshold for disk utilization on the __TOPDIR__ filesystem. |
226 |
|
|
# If the output from $Conf{DfPath} reports a percentage larger than |
227 |
|
|
# this number then no new regularly scheduled backups will be run. |
228 |
|
|
# However, user requested backups (which are usually incremental and |
229 |
|
|
# tend to be small) are still performed, independent of disk usage. |
230 |
|
|
# Also, currently running backups will not be terminated when the disk |
231 |
|
|
# usage exceeds this number. |
232 |
|
|
# |
233 |
|
|
$Conf{DfMaxUsagePct} = 95; |
234 |
|
|
|
235 |
|
|
# |
236 |
|
|
# How long BackupPC_trashClean sleeps in seconds between each check |
237 |
|
|
# of the trash directory. Once every 5 minutes should be reasonable. |
238 |
|
|
# |
239 |
|
|
$Conf{TrashCleanSleepSec} = 300; |
240 |
|
|
|
241 |
|
|
# |
242 |
|
|
# List of DHCP address ranges we search looking for PCs to backup. |
243 |
|
|
# This is an array of hashes for each class C address range. |
244 |
|
|
# This is only needed if hosts in the conf/hosts file have the |
245 |
|
|
# dhcp flag set. |
246 |
|
|
# |
247 |
|
|
# Examples: |
248 |
|
|
# # to specify 192.10.10.20 to 192.10.10.250 as the DHCP address pool |
249 |
|
|
# $Conf{DHCPAddressRanges} = [ |
250 |
|
|
# { |
251 |
|
|
# ipAddrBase => '192.10.10', |
252 |
|
|
# first => 20, |
253 |
|
|
# last => 250, |
254 |
|
|
# }, |
255 |
|
|
# ]; |
256 |
|
|
# # to specify two pools (192.10.10.20-250 and 192.10.11.10-50) |
257 |
|
|
# $Conf{DHCPAddressRanges} = [ |
258 |
|
|
# { |
259 |
|
|
# ipAddrBase => '192.10.10', |
260 |
|
|
# first => 20, |
261 |
|
|
# last => 250, |
262 |
|
|
# }, |
263 |
|
|
# { |
264 |
|
|
# ipAddrBase => '192.10.11', |
265 |
|
|
# first => 10, |
266 |
|
|
# last => 50, |
267 |
|
|
# }, |
268 |
|
|
# ]; |
269 |
|
|
# |
270 |
|
|
$Conf{DHCPAddressRanges} = []; |
271 |
|
|
|
272 |
|
|
# |
273 |
|
|
# These configuration settings aren't used by BackupPC, but simply |
274 |
|
|
# remember a few settings used by configure.pl during installation. |
275 |
|
|
# These are used by configure.pl when upgrading to new versions of |
276 |
|
|
# BackupPC. |
277 |
|
|
# |
278 |
|
|
$Conf{BackupPCUser} = ''; |
279 |
|
|
$Conf{CgiDir} = ''; |
280 |
|
|
$Conf{InstallDir} = ''; |
281 |
|
|
|
282 |
|
|
# |
283 |
|
|
# Whether BackupPC and the CGI script BackupPC_Admin verify that they |
284 |
|
|
# are really running as user $Conf{BackupPCUser}. If this flag is set |
285 |
|
|
# and the effective user id (euid) differs from $Conf{BackupPCUser} |
286 |
|
|
# then both scripts exit with an error. This catches cases where |
287 |
|
|
# BackupPC might be accidently started as root or the wrong user, |
288 |
|
|
# or if the CGI script is not installed correctly. |
289 |
|
|
# |
290 |
|
|
$Conf{BackupPCUserVerify} = 1; |
291 |
|
|
|
292 |
|
|
# |
293 |
|
|
# Maximum number of hardlinks supported by the $TopDir file system |
294 |
|
|
# that BackupPC uses. Most linux or unix file systems should support |
295 |
|
|
# at least 32000 hardlinks per file, or 64000 in other cases. If a pool |
296 |
|
|
# file already has this number of hardlinks, a new pool file is created |
297 |
|
|
# so that new hardlinks can be accommodated. This limit will only |
298 |
|
|
# be hit if an identical file appears at least this number of times |
299 |
|
|
# across all the backups. |
300 |
|
|
# |
301 |
|
|
$Conf{HardLinkMax} = 31999; |
302 |
|
|
|
303 |
|
|
########################################################################### |
304 |
|
|
# What to backup and when to do it |
305 |
|
|
# (can be overridden in the per-PC config.pl) |
306 |
|
|
########################################################################### |
307 |
|
|
# |
308 |
|
|
# Name of the host share that is backed up when using SMB. This can be a |
309 |
|
|
# string or an array of strings if there are multiple shares per host. |
310 |
|
|
# Examples: |
311 |
|
|
# |
312 |
|
|
# $Conf{SmbShareName} = 'c'; # backup 'c' share |
313 |
|
|
# $Conf{SmbShareName} = ['c', 'd']; # backup 'c' and 'd' shares |
314 |
|
|
# |
315 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
316 |
|
|
# |
317 |
|
|
$Conf{SmbShareName} = 'C$'; |
318 |
|
|
|
319 |
|
|
# |
320 |
|
|
# Smbclient share user name. This is passed to smbclient's -U argument. |
321 |
|
|
# |
322 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
323 |
|
|
# |
324 |
|
|
$Conf{SmbShareUserName} = ''; |
325 |
|
|
|
326 |
|
|
# |
327 |
|
|
# Smbclient share password. This is passed to smbclient via its PASSWD |
328 |
|
|
# environment variable. There are several ways you can tell BackupPC |
329 |
|
|
# the smb share password. In each case you should be very careful about |
330 |
|
|
# security. If you put the password here, make sure that this file is |
331 |
|
|
# not readable by regular users! See the "Setting up config.pl" section |
332 |
|
|
# in the documentation for more information. |
333 |
|
|
# |
334 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
335 |
|
|
# |
336 |
|
|
$Conf{SmbSharePasswd} = ''; |
337 |
|
|
|
338 |
|
|
# |
339 |
|
|
# Which host directories to backup when using tar transport. This can be a |
340 |
|
|
# string or an array of strings if there are multiple directories to |
341 |
|
|
# backup per host. Examples: |
342 |
|
|
# |
343 |
|
|
# $Conf{TarShareName} = '/'; # backup everything |
344 |
|
|
# $Conf{TarShareName} = '/home'; # only backup /home |
345 |
|
|
# $Conf{TarShareName} = ['/home', '/src']; # backup /home and /src |
346 |
|
|
# |
347 |
|
|
# The fact this parameter is called 'TarShareName' is for historical |
348 |
|
|
# consistency with the Smb transport options. You can use any valid |
349 |
|
|
# directory on the client: there is no need for it to correspond to |
350 |
|
|
# any Smb share or device mount point. |
351 |
|
|
# |
352 |
|
|
# Note also that you can also use $Conf{BackupFilesOnly} to specify |
353 |
|
|
# a specific list of directories to backup. It's more efficient to |
354 |
|
|
# use this option instead of $Conf{TarShareName} since a new tar is |
355 |
|
|
# run for each entry in $Conf{TarShareName}. |
356 |
|
|
# |
357 |
|
|
# On the other hand, if you add --one-file-system to $Conf{TarClientCmd} |
358 |
|
|
# you can backup each file system separately, which makes restoring one |
359 |
|
|
# bad file system easier. In this case you would list all of the mount |
360 |
|
|
# points here, since you can't get the same result with |
361 |
|
|
# $Conf{BackupFilesOnly}: |
362 |
|
|
# |
363 |
|
|
# $Conf{TarShareName} = ['/', '/var', '/data', '/boot']; |
364 |
|
|
# |
365 |
|
|
# This setting only matters if $Conf{XferMethod} = 'tar'. |
366 |
|
|
# |
367 |
|
|
$Conf{TarShareName} = '/'; |
368 |
|
|
|
369 |
|
|
# |
370 |
|
|
# Minimum period in days between full backups. A full dump will only be |
371 |
|
|
# done if at least this much time has elapsed since the last full dump, |
372 |
|
|
# and at least $Conf{IncrPeriod} days has elapsed since the last |
373 |
|
|
# successful dump. |
374 |
|
|
# |
375 |
|
|
# Typically this is set slightly less than an integer number of days. The |
376 |
|
|
# time taken for the backup, plus the granularity of $Conf{WakeupSchedule} |
377 |
|
|
# will make the actual backup interval a bit longer. |
378 |
|
|
# |
379 |
|
|
# There are two special values for $Conf{FullPeriod}: |
380 |
|
|
# |
381 |
|
|
# -1 Don't do any regular backups on this machine. Manually |
382 |
|
|
# requested backups (via the CGI interface) will still occur. |
383 |
|
|
# |
384 |
|
|
# -2 Don't do any backups on this machine. Manually requested |
385 |
|
|
# backups (via the CGI interface) will be ignored. |
386 |
|
|
# |
387 |
|
|
# These special settings are useful for a client that is no longer |
388 |
|
|
# being backed up (eg: a retired machine), but you wish to keep the |
389 |
|
|
# last backups available for browsing or restoring to other machines. |
390 |
|
|
# |
391 |
|
|
$Conf{FullPeriod} = 6.97; |
392 |
|
|
|
393 |
|
|
# |
394 |
|
|
# Minimum period in days between incremental backups (a user requested |
395 |
|
|
# incremental backup will be done anytime on demand). |
396 |
|
|
# |
397 |
|
|
# Typically this is set slightly less than an integer number of days. The |
398 |
|
|
# time taken for the backup, plus the granularity of $Conf{WakeupSchedule} |
399 |
|
|
# will make the actual backup interval a bit longer. |
400 |
|
|
# |
401 |
|
|
$Conf{IncrPeriod} = 0.97; |
402 |
|
|
|
403 |
|
|
# |
404 |
|
|
# Number of full backups to keep. Must be >= 1. |
405 |
|
|
# |
406 |
|
|
# In the steady state, each time a full backup completes successfully |
407 |
|
|
# the oldest one is removed. If this number is decreased, the |
408 |
|
|
# extra old backups will be removed. |
409 |
|
|
# |
410 |
|
|
# If filling of incremental dumps is off the oldest backup always |
411 |
|
|
# has to be a full (ie: filled) dump. This might mean one or two |
412 |
|
|
# extra full dumps are kept until the oldest incremental backups expire. |
413 |
|
|
# |
414 |
|
|
# Exponential backup expiry is also supported. This allows you to specify: |
415 |
|
|
# |
416 |
|
|
# - num fulls to keep at intervals of 1 * $Conf{FullPeriod}, followed by |
417 |
|
|
# - num fulls to keep at intervals of 2 * $Conf{FullPeriod}, |
418 |
|
|
# - num fulls to keep at intervals of 4 * $Conf{FullPeriod}, |
419 |
|
|
# - num fulls to keep at intervals of 8 * $Conf{FullPeriod}, |
420 |
|
|
# - num fulls to keep at intervals of 16 * $Conf{FullPeriod}, |
421 |
|
|
# |
422 |
|
|
# and so on. This works by deleting every other full as each expiry |
423 |
|
|
# boundary is crossed. |
424 |
|
|
# |
425 |
|
|
# Exponential expiry is specified using an array for $Conf{FullKeepCnt}: |
426 |
|
|
# |
427 |
|
|
# $Conf{FullKeepCnt} = [4, 2, 3]; |
428 |
|
|
# |
429 |
|
|
# Entry #n specifies how many fulls to keep at an interval of |
430 |
|
|
# 2^n * $Conf{FullPeriod} (ie: 1, 2, 4, 8, 16, 32, ...). |
431 |
|
|
# |
432 |
|
|
# The example above specifies keeping 4 of the most recent full backups |
433 |
|
|
# (1 week interval) two full backups at 2 week intervals, and 3 full |
434 |
|
|
# backups at 4 week intervals, eg: |
435 |
|
|
# |
436 |
|
|
# full 0 19 weeks old \ |
437 |
|
|
# full 1 15 weeks old >--- 3 backups at 4 * $Conf{FullPeriod} |
438 |
|
|
# full 2 11 weeks old / |
439 |
|
|
# full 3 7 weeks old \____ 2 backups at 2 * $Conf{FullPeriod} |
440 |
|
|
# full 4 5 weeks old / |
441 |
|
|
# full 5 3 weeks old \ |
442 |
|
|
# full 6 2 weeks old \___ 4 backups at 1 * $Conf{FullPeriod} |
443 |
|
|
# full 7 1 week old / |
444 |
|
|
# full 8 current / |
445 |
|
|
# |
446 |
|
|
# On a given week the spacing might be less than shown as each backup |
447 |
|
|
# ages through each expiry period. For example, one week later, a |
448 |
|
|
# new full is completed and the oldest is deleted, giving: |
449 |
|
|
# |
450 |
|
|
# full 0 16 weeks old \ |
451 |
|
|
# full 1 12 weeks old >--- 3 backups at 4 * $Conf{FullPeriod} |
452 |
|
|
# full 2 8 weeks old / |
453 |
|
|
# full 3 6 weeks old \____ 2 backups at 2 * $Conf{FullPeriod} |
454 |
|
|
# full 4 4 weeks old / |
455 |
|
|
# full 5 3 weeks old \ |
456 |
|
|
# full 6 2 weeks old \___ 4 backups at 1 * $Conf{FullPeriod} |
457 |
|
|
# full 7 1 week old / |
458 |
|
|
# full 8 current / |
459 |
|
|
# |
460 |
|
|
# You can specify 0 as a count (except in the first entry), and the |
461 |
|
|
# array can be as long as you wish. For example: |
462 |
|
|
# |
463 |
|
|
# $Conf{FullKeepCnt} = [4, 0, 4, 0, 0, 2]; |
464 |
|
|
# |
465 |
|
|
# This will keep 10 full dumps, 4 most recent at 1 * $Conf{FullPeriod}, |
466 |
|
|
# followed by 4 at an interval of 4 * $Conf{FullPeriod} (approx 1 month |
467 |
|
|
# apart), and then 2 at an interval of 32 * $Conf{FullPeriod} (approx |
468 |
|
|
# 7-8 months apart). |
469 |
|
|
# |
470 |
|
|
# Example: these two settings are equivalent and both keep just |
471 |
|
|
# the four most recent full dumps: |
472 |
|
|
# |
473 |
|
|
# $Conf{FullKeepCnt} = 4; |
474 |
|
|
# $Conf{FullKeepCnt} = [4]; |
475 |
|
|
# |
476 |
|
|
$Conf{FullKeepCnt} = 1; |
477 |
|
|
|
478 |
|
|
# |
479 |
|
|
# Very old full backups are removed after $Conf{FullAgeMax} days. However, |
480 |
|
|
# we keep at least $Conf{FullKeepCntMin} full backups no matter how old |
481 |
|
|
# they are. |
482 |
|
|
# |
483 |
|
|
# Note that $Conf{FullAgeMax} will be increased to $Conf{FullAgeMax} |
484 |
|
|
# times $Conf{FullPeriod} if $Conf{FullAgeMax} specifies enough |
485 |
|
|
# full backups to exceed $Conf{FullAgeMax}. |
486 |
|
|
# |
487 |
|
|
$Conf{FullKeepCntMin} = 1; |
488 |
|
|
$Conf{FullAgeMax} = 90; |
489 |
|
|
|
490 |
|
|
# |
491 |
|
|
# Number of incremental backups to keep. Must be >= 1. |
492 |
|
|
# |
493 |
|
|
# In the steady state, each time an incr backup completes successfully |
494 |
|
|
# the oldest one is removed. If this number is decreased, the |
495 |
|
|
# extra old backups will be removed. |
496 |
|
|
# |
497 |
|
|
$Conf{IncrKeepCnt} = 6; |
498 |
|
|
|
499 |
|
|
# |
500 |
|
|
# Very old incremental backups are removed after $Conf{IncrAgeMax} days. |
501 |
|
|
# However, we keep at least $Conf{IncrKeepCntMin} incremental backups no |
502 |
|
|
# matter how old they are. |
503 |
|
|
# |
504 |
|
|
$Conf{IncrKeepCntMin} = 1; |
505 |
|
|
$Conf{IncrAgeMax} = 30; |
506 |
|
|
|
507 |
|
|
# |
508 |
|
|
# A failed full backup is saved as a partial backup. The rsync |
509 |
|
|
# XferMethod can take advantage of the partial full when the next |
510 |
|
|
# backup is run. This parameter sets the age of the partial full |
511 |
|
|
# in days: if the partial backup is older than this number of |
512 |
|
|
# days, then rsync will ignore (not use) the partial full when |
513 |
|
|
# the next backup is run. If you set this to a negative value |
514 |
|
|
# then no partials will be saved. If you set this to 0, partials |
515 |
|
|
# will be saved, but will not be used by the next backup. |
516 |
|
|
# |
517 |
|
|
# The default setting of 3 days means that a partial older than |
518 |
|
|
# 3 days is ignored when the next full backup is done. |
519 |
|
|
# |
520 |
|
|
$Conf{PartialAgeMax} = 3; |
521 |
|
|
|
522 |
|
|
# |
523 |
|
|
# Whether incremental backups are filled. "Filling" means that the |
524 |
|
|
# most recent full (or filled) dump is merged into the new incremental |
525 |
|
|
# dump using hardlinks. This makes an incremental dump look like a |
526 |
|
|
# full dump. Prior to v1.03 all incremental backups were filled. |
527 |
|
|
# In v1.4.0 and later the default is off. |
528 |
|
|
# |
529 |
|
|
# BackupPC, and the cgi interface in particular, do the right thing on |
530 |
|
|
# un-filled incremental backups. It will correctly display the merged |
531 |
|
|
# incremental backup with the most recent filled backup, giving the |
532 |
|
|
# un-filled incremental backups a filled appearance. That means it |
533 |
|
|
# invisible to the user whether incremental dumps are filled or not. |
534 |
|
|
# |
535 |
|
|
# Filling backups takes a little extra disk space, and it does cost |
536 |
|
|
# some extra disk activity for filling, and later removal. Filling |
537 |
|
|
# is no longer useful, since file mangling and compression doesn't |
538 |
|
|
# make a filled backup very useful. It's likely the filling option |
539 |
|
|
# will be removed from future versions: filling will be delegated to |
540 |
|
|
# the display and extraction of backup data. |
541 |
|
|
# |
542 |
|
|
# If filling is off, BackupPC makes sure that the oldest backup is |
543 |
|
|
# a full, otherwise the following incremental backups will be |
544 |
|
|
# incomplete. This might mean an extra full backup has to be |
545 |
|
|
# kept until the following incremental backups expire. |
546 |
|
|
# |
547 |
|
|
# The default is off. You can turn this on or off at any |
548 |
|
|
# time without affecting existing backups. |
549 |
|
|
# |
550 |
|
|
$Conf{IncrFill} = 0; |
551 |
|
|
|
552 |
|
|
# |
553 |
|
|
# Number of restore logs to keep. BackupPC remembers information about |
554 |
|
|
# each restore request. This number per client will be kept around before |
555 |
|
|
# the oldest ones are pruned. |
556 |
|
|
# |
557 |
|
|
# Note: files/dirs delivered via Zip or Tar downloads don't count as |
558 |
|
|
# restores. Only the first restore option (where the files and dirs |
559 |
|
|
# are written to the host) count as restores that are logged. |
560 |
|
|
# |
561 |
|
|
$Conf{RestoreInfoKeepCnt} = 10; |
562 |
|
|
|
563 |
|
|
# |
564 |
|
|
# Number of archive logs to keep. BackupPC remembers information |
565 |
|
|
# about each archive request. This number per archive client will |
566 |
|
|
# be kept around before the oldest ones are pruned. |
567 |
|
|
# |
568 |
|
|
$Conf{ArchiveInfoKeepCnt} = 10; |
569 |
|
|
|
570 |
|
|
# |
571 |
|
|
# List of directories or files to backup. If this is defined, only these |
572 |
|
|
# directories or files will be backed up. |
573 |
|
|
# |
574 |
|
|
# For Smb, only one of $Conf{BackupFilesExclude} and $Conf{BackupFilesOnly} |
575 |
|
|
# can be specified per share. If both are set for a particular share, then |
576 |
|
|
# $Conf{BackupFilesOnly} takes precedence and $Conf{BackupFilesExclude} |
577 |
|
|
# is ignored. |
578 |
|
|
# |
579 |
|
|
# This can be set to a string, an array of strings, or, in the case |
580 |
|
|
# of multiple shares, a hash of strings or arrays. A hash is used |
581 |
|
|
# to give a list of directories or files to backup for each share |
582 |
|
|
# (the share name is the key). If this is set to just a string or |
583 |
|
|
# array, and $Conf{SmbShareName} contains multiple share names, then |
584 |
|
|
# the setting is assumed to apply all shares. |
585 |
|
|
# |
586 |
|
|
# Examples: |
587 |
|
|
# $Conf{BackupFilesOnly} = '/myFiles'; |
588 |
|
|
# $Conf{BackupFilesOnly} = ['/myFiles']; # same as first example |
589 |
|
|
# $Conf{BackupFilesOnly} = ['/myFiles', '/important']; |
590 |
|
|
# $Conf{BackupFilesOnly} = { |
591 |
|
|
# 'c' => ['/myFiles', '/important'], # these are for 'c' share |
592 |
|
|
# 'd' => ['/moreFiles', '/archive'], # these are for 'd' share |
593 |
|
|
# }; |
594 |
|
|
# |
595 |
|
|
$Conf{BackupFilesOnly} = undef; |
596 |
|
|
|
597 |
|
|
# |
598 |
|
|
# List of directories or files to exclude from the backup. For Smb, |
599 |
|
|
# only one of $Conf{BackupFilesExclude} and $Conf{BackupFilesOnly} |
600 |
|
|
# can be specified per share. If both are set for a particular share, |
601 |
|
|
# then $Conf{BackupFilesOnly} takes precedence and |
602 |
|
|
# $Conf{BackupFilesExclude} is ignored. |
603 |
|
|
# |
604 |
|
|
# This can be set to a string, an array of strings, or, in the case |
605 |
|
|
# of multiple shares, a hash of strings or arrays. A hash is used |
606 |
|
|
# to give a list of directories or files to exclude for each share |
607 |
|
|
# (the share name is the key). If this is set to just a string or |
608 |
|
|
# array, and $Conf{SmbShareName} contains multiple share names, then |
609 |
|
|
# the setting is assumed to apply to all shares. |
610 |
|
|
# |
611 |
|
|
# The exact behavior is determined by the underlying transport program, |
612 |
|
|
# smbclient or tar. For smbclient the exlclude file list is passed into |
613 |
|
|
# the X option. Simple shell wild-cards using "*" or "?" are allowed. |
614 |
|
|
# |
615 |
|
|
# For tar, if the exclude file contains a "/" it is assumed to be anchored |
616 |
|
|
# at the start of the string. Since all the tar paths start with "./", |
617 |
|
|
# BackupPC prepends a "." if the exclude file starts with a "/". Note |
618 |
|
|
# that GNU tar version >= 1.13.7 is required for the exclude option to |
619 |
|
|
# work correctly. For linux or unix machines you should add |
620 |
|
|
# "/proc" to $Conf{BackupFilesExclude} unless you have specified |
621 |
|
|
# --one-file-system in $Conf{TarClientCmd} or --one-file-system in |
622 |
|
|
# $Conf{RsyncArgs}. Also, for tar, do not use a trailing "/" in |
623 |
|
|
# the directory name: a trailing "/" causes the name to not match |
624 |
|
|
# and the directory will not be excluded. |
625 |
|
|
# |
626 |
|
|
# Users report that for smbclient you should specify a directory |
627 |
|
|
# followed by "/*", eg: "/proc/*", instead of just "/proc". |
628 |
|
|
# |
629 |
|
|
# Examples: |
630 |
|
|
# $Conf{BackupFilesExclude} = '/temp'; |
631 |
|
|
# $Conf{BackupFilesExclude} = ['/temp']; # same as first example |
632 |
|
|
# $Conf{BackupFilesExclude} = ['/temp', '/winnt/tmp']; |
633 |
|
|
# $Conf{BackupFilesExclude} = { |
634 |
|
|
# 'c' => ['/temp', '/winnt/tmp'], # these are for 'c' share |
635 |
|
|
# 'd' => ['/junk', '/dont_back_this_up'], # these are for 'd' share |
636 |
|
|
# }; |
637 |
|
|
# |
638 |
|
|
$Conf{BackupFilesExclude} = undef; |
639 |
|
|
|
640 |
|
|
# |
641 |
|
|
# PCs that are always or often on the network can be backed up after |
642 |
|
|
# hours, to reduce PC, network and server load during working hours. For |
643 |
|
|
# each PC a count of consecutive good pings is maintained. Once a PC has |
644 |
|
|
# at least $Conf{BlackoutGoodCnt} consecutive good pings it is subject |
645 |
|
|
# to "blackout" and not backed up during hours and days specified by |
646 |
|
|
# $Conf{BlackoutPeriods}. |
647 |
|
|
# |
648 |
|
|
# To allow for periodic rebooting of a PC or other brief periods when a |
649 |
|
|
# PC is not on the network, a number of consecutive bad pings is allowed |
650 |
|
|
# before the good ping count is reset. This parameter is |
651 |
|
|
# $Conf{BlackoutBadPingLimit}. |
652 |
|
|
# |
653 |
|
|
# Note that bad and good pings don't occur with the same interval. If a |
654 |
|
|
# machine is always on the network, it will only be pinged roughly once |
655 |
|
|
# every $Conf{IncrPeriod} (eg: once per day). So a setting for |
656 |
|
|
# $Conf{BlackoutGoodCnt} of 7 means it will take around 7 days for a |
657 |
|
|
# machine to be subject to blackout. On the other hand, if a ping is |
658 |
|
|
# failed, it will be retried roughly every time BackupPC wakes up, eg, |
659 |
|
|
# every one or two hours. So a setting for $Conf{BlackoutBadPingLimit} of |
660 |
|
|
# 3 means that the PC will lose its blackout status after 3-6 hours of |
661 |
|
|
# unavailability. |
662 |
|
|
# |
663 |
|
|
# To disable the blackout feature set $Conf{BlackoutGoodCnt} to a negative |
664 |
|
|
# value. A value of 0 will make all machines subject to blackout. But |
665 |
|
|
# if you don't want to do any backups during the day it would be easier |
666 |
|
|
# to just set $Conf{WakeupSchedule} to a restricted schedule. |
667 |
|
|
# |
668 |
|
|
$Conf{BlackoutBadPingLimit} = 3; |
669 |
|
|
$Conf{BlackoutGoodCnt} = 7; |
670 |
|
|
|
671 |
|
|
# |
672 |
|
|
# One or more blackout periods can be specified. If a client is |
673 |
|
|
# subject to blackout then no regular (non-manual) backups will |
674 |
|
|
# be started during any of these periods. hourBegin and hourEnd |
675 |
|
|
# specify hours fro midnight and weekDays is a list of days of |
676 |
|
|
# the week where 0 is Sunday, 1 is Monday etc. |
677 |
|
|
# |
678 |
|
|
# For example: |
679 |
|
|
# |
680 |
|
|
# $Conf{BlackoutPeriods} = [ |
681 |
|
|
# { |
682 |
|
|
# hourBegin => 7.0, |
683 |
|
|
# hourEnd => 19.5, |
684 |
|
|
# weekDays => [1, 2, 3, 4, 5], |
685 |
|
|
# }, |
686 |
|
|
# ]; |
687 |
|
|
# |
688 |
|
|
# specifies one blackout period from 7:00am to 7:30pm local time |
689 |
|
|
# on Mon-Fri. |
690 |
|
|
# |
691 |
|
|
# The blackout period can also span midnight by setting |
692 |
|
|
# hourBegin > hourEnd, eg: |
693 |
|
|
# |
694 |
|
|
# $Conf{BlackoutPeriods} = [ |
695 |
|
|
# { |
696 |
|
|
# hourBegin => 7.0, |
697 |
|
|
# hourEnd => 19.5, |
698 |
|
|
# weekDays => [1, 2, 3, 4, 5], |
699 |
|
|
# }, |
700 |
|
|
# { |
701 |
|
|
# hourBegin => 23, |
702 |
|
|
# hourEnd => 5, |
703 |
|
|
# weekDays => [5, 6], |
704 |
|
|
# }, |
705 |
|
|
# ]; |
706 |
|
|
# |
707 |
|
|
# This specifies one blackout period from 7:00am to 7:30pm local time |
708 |
|
|
# on Mon-Fri, and a second period from 11pm to 5am on Friday and |
709 |
|
|
# Saturday night. |
710 |
|
|
# |
711 |
|
|
$Conf{BlackoutPeriods} = [ |
712 |
|
|
{ |
713 |
|
|
hourBegin => 7.0, |
714 |
|
|
hourEnd => 19.5, |
715 |
|
|
weekDays => [1, 2, 3, 4, 5], |
716 |
|
|
}, |
717 |
|
|
]; |
718 |
|
|
|
719 |
|
|
# |
720 |
|
|
# A backup of a share that has zero files is considered fatal. This is |
721 |
|
|
# used to catch miscellaneous Xfer errors that result in no files being |
722 |
|
|
# backed up. If you have shares that might be empty (and therefore an |
723 |
|
|
# empty backup is valid) you should set this flag to 0. |
724 |
|
|
# |
725 |
|
|
$Conf{BackupZeroFilesIsFatal} = 1; |
726 |
|
|
|
727 |
|
|
########################################################################### |
728 |
|
|
# General per-PC configuration settings |
729 |
|
|
# (can be overridden in the per-PC config.pl) |
730 |
|
|
########################################################################### |
731 |
|
|
# |
732 |
|
|
# What transport method to use to backup each host. If you have |
733 |
|
|
# a mixed set of WinXX and linux/unix hosts you will need to override |
734 |
|
|
# this in the per-PC config.pl. |
735 |
|
|
# |
736 |
|
|
# The valid values are: |
737 |
|
|
# |
738 |
|
|
# - 'smb': backup and restore via smbclient and the SMB protocol. |
739 |
|
|
# Easiest choice for WinXX. |
740 |
|
|
# |
741 |
|
|
# - 'rsync': backup and restore via rsync (via rsh or ssh). |
742 |
|
|
# Best choice for linux/unix. Good choice also for WinXX. |
743 |
|
|
# |
744 |
dpavlin |
316 |
# - 'rsyncd': backup and restore via rsync daemon on the client. |
745 |
dpavlin |
1 |
# Best choice for linux/unix if you have rsyncd running on |
746 |
|
|
# the client. Good choice also for WinXX. |
747 |
|
|
# |
748 |
|
|
# - 'tar': backup and restore via tar, tar over ssh, rsh or nfs. |
749 |
|
|
# Good choice for linux/unix. |
750 |
|
|
# |
751 |
|
|
# - 'archive': host is a special archive host. Backups are not done. |
752 |
|
|
# An archive host is used to archive other host's backups |
753 |
|
|
# to permanent media, such as tape, CDR or DVD. |
754 |
|
|
# |
755 |
|
|
# |
756 |
|
|
$Conf{XferMethod} = 'smb'; |
757 |
|
|
|
758 |
|
|
# |
759 |
|
|
# Level of verbosity in Xfer log files. 0 means be quiet, 1 will give |
760 |
|
|
# will give one line per file, 2 will also show skipped files on |
761 |
|
|
# incrementals, higher values give more output. |
762 |
|
|
# |
763 |
|
|
$Conf{XferLogLevel} = 1; |
764 |
|
|
|
765 |
|
|
# |
766 |
|
|
# Full path for smbclient. Security caution: normal users should not |
767 |
|
|
# allowed to write to this file or directory. |
768 |
|
|
# |
769 |
|
|
# smbclient is from the Samba distribution. smbclient is used to |
770 |
|
|
# actually extract the incremental or full dump of the share filesystem |
771 |
|
|
# from the PC. |
772 |
|
|
# |
773 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
774 |
|
|
# |
775 |
|
|
$Conf{SmbClientPath} = '/usr/bin/smbclient'; |
776 |
|
|
|
777 |
|
|
# |
778 |
|
|
# Command to run smbclient for a full dump. |
779 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
780 |
|
|
# |
781 |
|
|
# The following variables are substituted at run-time: |
782 |
|
|
# |
783 |
|
|
# $smbClientPath same as $Conf{SmbClientPath} |
784 |
|
|
# $host host to backup/restore |
785 |
|
|
# $hostIP host IP address |
786 |
|
|
# $shareName share name |
787 |
|
|
# $userName user name |
788 |
|
|
# $fileList list of files to backup (based on exclude/include) |
789 |
|
|
# $I_option optional -I option to smbclient |
790 |
|
|
# $X_option exclude option (if $fileList is an exclude list) |
791 |
|
|
# $timeStampFile start time for incremental dump |
792 |
|
|
# |
793 |
|
|
$Conf{SmbClientFullCmd} = '$smbClientPath \\\\$host\\$shareName' |
794 |
|
|
. ' $I_option -U $userName -E -N -d 1' |
795 |
|
|
. ' -c tarmode\\ full -Tc$X_option - $fileList'; |
796 |
|
|
|
797 |
|
|
# |
798 |
|
|
# Command to run smbclient for an incremental dump. |
799 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
800 |
|
|
# |
801 |
|
|
# Same variable substitutions are applied as $Conf{SmbClientFullCmd}. |
802 |
|
|
# |
803 |
|
|
$Conf{SmbClientIncrCmd} = '$smbClientPath \\\\$host\\$shareName' |
804 |
|
|
. ' $I_option -U $userName -E -N -d 1' |
805 |
|
|
. ' -c tarmode\\ full -TcN$X_option $timeStampFile - $fileList'; |
806 |
|
|
|
807 |
|
|
# |
808 |
|
|
# Command to run smbclient for a restore. |
809 |
|
|
# This setting only matters if $Conf{XferMethod} = 'smb'. |
810 |
|
|
# |
811 |
|
|
# Same variable substitutions are applied as $Conf{SmbClientFullCmd}. |
812 |
|
|
# |
813 |
|
|
# If your smb share is read-only then direct restores will fail. |
814 |
|
|
# You should set $Conf{SmbClientRestoreCmd} to undef and the |
815 |
|
|
# corresponding CGI restore option will be removed. |
816 |
|
|
# |
817 |
|
|
$Conf{SmbClientRestoreCmd} = '$smbClientPath \\\\$host\\$shareName' |
818 |
|
|
. ' $I_option -U $userName -E -N -d 1' |
819 |
|
|
. ' -c tarmode\\ full -Tx -'; |
820 |
|
|
|
821 |
|
|
# |
822 |
|
|
# Full command to run tar on the client. GNU tar is required. You will |
823 |
|
|
# need to fill in the correct paths for ssh2 on the local host (server) |
824 |
|
|
# and GNU tar on the client. Security caution: normal users should not |
825 |
|
|
# allowed to write to these executable files or directories. |
826 |
|
|
# |
827 |
|
|
# See the documentation for more information about setting up ssh2 keys. |
828 |
|
|
# |
829 |
|
|
# If you plan to use NFS then tar just runs locally and ssh2 is not needed. |
830 |
|
|
# For example, assuming the client filesystem is mounted below /mnt/hostName, |
831 |
|
|
# you could use something like: |
832 |
|
|
# |
833 |
|
|
# $Conf{TarClientCmd} = '$tarPath -c -v -f - -C /mnt/$host/$shareName' |
834 |
|
|
# . ' --totals'; |
835 |
|
|
# |
836 |
|
|
# In the case of NFS or rsh you need to make sure BackupPC's privileges |
837 |
|
|
# are sufficient to read all the files you want to backup. Also, you |
838 |
|
|
# will probably want to add "/proc" to $Conf{BackupFilesExclude}. |
839 |
|
|
# |
840 |
|
|
# The following variables are substituted at run-time: |
841 |
|
|
# |
842 |
|
|
# $host host name |
843 |
|
|
# $hostIP host's IP address |
844 |
|
|
# $incrDate newer-than date for incremental backups |
845 |
|
|
# $shareName share name to backup (ie: top-level directory path) |
846 |
|
|
# $fileList specific files to backup or exclude |
847 |
|
|
# $tarPath same as $Conf{TarClientPath} |
848 |
|
|
# $sshPath same as $Conf{SshPath} |
849 |
|
|
# |
850 |
|
|
# If a variable is followed by a "+" it is shell escaped. This is |
851 |
|
|
# necessary for the command part of ssh or rsh, since it ends up |
852 |
|
|
# getting passed through the shell. |
853 |
|
|
# |
854 |
|
|
# This setting only matters if $Conf{XferMethod} = 'tar'. |
855 |
|
|
# |
856 |
|
|
$Conf{TarClientCmd} = '$sshPath -q -x -n -l root $host' |
857 |
|
|
. ' $tarPath -c -v -f - -C $shareName+' |
858 |
|
|
. ' --totals'; |
859 |
|
|
|
860 |
|
|
# |
861 |
|
|
# Extra tar arguments for full backups. Several variables are substituted at |
862 |
|
|
# run-time. See $Conf{TarClientCmd} for the list of variable substitutions. |
863 |
|
|
# |
864 |
|
|
# If you are running tar locally (ie: without rsh or ssh) then remove the |
865 |
|
|
# "+" so that the argument is no longer shell escaped. |
866 |
|
|
# |
867 |
|
|
# This setting only matters if $Conf{XferMethod} = 'tar'. |
868 |
|
|
# |
869 |
|
|
$Conf{TarFullArgs} = '$fileList+'; |
870 |
|
|
|
871 |
|
|
# |
872 |
|
|
# Extra tar arguments for incr backups. Several variables are substituted at |
873 |
|
|
# run-time. See $Conf{TarClientCmd} for the list of variable substitutions. |
874 |
|
|
# |
875 |
|
|
# Note that GNU tar has several methods for specifying incremental backups, |
876 |
|
|
# including: |
877 |
|
|
# |
878 |
|
|
# --newer-mtime $incrDate+ |
879 |
|
|
# This causes a file to be included if the modification time is |
880 |
|
|
# later than $incrDate (meaning its contents might have changed). |
881 |
|
|
# But changes in the ownership or modes will not qualify the |
882 |
|
|
# file to be included in an incremental. |
883 |
|
|
# |
884 |
|
|
# --newer=$incrDate+ |
885 |
|
|
# This causes the file to be included if any attribute of the |
886 |
|
|
# file is later than $incrDate, meaning either attributes or |
887 |
|
|
# the modification time. This is the default method. Do |
888 |
|
|
# not use --atime-preserve in $Conf{TarClientCmd} above, |
889 |
|
|
# otherwise resetting the atime (access time) counts as an |
890 |
|
|
# attribute change, meaning the file will always be included |
891 |
|
|
# in each new incremental dump. |
892 |
|
|
# |
893 |
|
|
# If you are running tar locally (ie: without rsh or ssh) then remove the |
894 |
|
|
# "+" so that the argument is no longer shell escaped. |
895 |
|
|
# |
896 |
|
|
# This setting only matters if $Conf{XferMethod} = 'tar'. |
897 |
|
|
# |
898 |
|
|
$Conf{TarIncrArgs} = '--newer=$incrDate+ $fileList+'; |
899 |
|
|
|
900 |
|
|
# |
901 |
|
|
# Full command to run tar for restore on the client. GNU tar is required. |
902 |
|
|
# This can be the same as $Conf{TarClientCmd}, with tar's -c replaced by -x |
903 |
|
|
# and ssh's -n removed. |
904 |
|
|
# |
905 |
|
|
# See $Conf{TarClientCmd} for full details. |
906 |
|
|
# |
907 |
|
|
# This setting only matters if $Conf{XferMethod} = "tar". |
908 |
|
|
# |
909 |
|
|
# If you want to disable direct restores using tar, you should set |
910 |
|
|
# $Conf{TarClientRestoreCmd} to undef and the corresponding CGI |
911 |
|
|
# restore option will be removed. |
912 |
|
|
# |
913 |
|
|
$Conf{TarClientRestoreCmd} = '$sshPath -q -x -l root $host' |
914 |
|
|
. ' $tarPath -x -p --numeric-owner --same-owner' |
915 |
|
|
. ' -v -f - -C $shareName+'; |
916 |
|
|
|
917 |
|
|
# |
918 |
|
|
# Full path for tar on the client. Security caution: normal users should not |
919 |
|
|
# allowed to write to this file or directory. |
920 |
|
|
# |
921 |
|
|
# This setting only matters if $Conf{XferMethod} = 'tar'. |
922 |
|
|
# |
923 |
|
|
$Conf{TarClientPath} = '/bin/tar'; |
924 |
|
|
|
925 |
|
|
# |
926 |
|
|
# Path to rsync executable on the client |
927 |
|
|
# |
928 |
|
|
$Conf{RsyncClientPath} = '/bin/rsync'; |
929 |
|
|
|
930 |
|
|
# |
931 |
|
|
# Full command to run rsync on the client machine. The following variables |
932 |
|
|
# are substituted at run-time: |
933 |
|
|
# |
934 |
|
|
# $host host name being backed up |
935 |
|
|
# $hostIP host's IP address |
936 |
|
|
# $shareName share name to backup (ie: top-level directory path) |
937 |
|
|
# $rsyncPath same as $Conf{RsyncClientPath} |
938 |
|
|
# $sshPath same as $Conf{SshPath} |
939 |
|
|
# $argList argument list, built from $Conf{RsyncArgs}, |
940 |
|
|
# $shareName, $Conf{BackupFilesExclude} and |
941 |
|
|
# $Conf{BackupFilesOnly} |
942 |
|
|
# |
943 |
|
|
# This setting only matters if $Conf{XferMethod} = 'rsync'. |
944 |
|
|
# |
945 |
|
|
$Conf{RsyncClientCmd} = '$sshPath -q -x -l root $host $rsyncPath $argList+'; |
946 |
|
|
|
947 |
|
|
# |
948 |
|
|
# Full command to run rsync for restore on the client. The following |
949 |
|
|
# variables are substituted at run-time: |
950 |
|
|
# |
951 |
|
|
# $host host name being backed up |
952 |
|
|
# $hostIP host's IP address |
953 |
|
|
# $shareName share name to backup (ie: top-level directory path) |
954 |
|
|
# $rsyncPath same as $Conf{RsyncClientPath} |
955 |
|
|
# $sshPath same as $Conf{SshPath} |
956 |
|
|
# $argList argument list, built from $Conf{RsyncArgs}, |
957 |
|
|
# $shareName, $Conf{BackupFilesExclude} and |
958 |
|
|
# $Conf{BackupFilesOnly} |
959 |
|
|
# |
960 |
|
|
# This setting only matters if $Conf{XferMethod} = 'rsync'. |
961 |
|
|
# |
962 |
|
|
$Conf{RsyncClientRestoreCmd} = '$sshPath -q -x -l root $host $rsyncPath $argList+'; |
963 |
|
|
|
964 |
|
|
# |
965 |
|
|
# Share name to backup. For $Conf{XferMethod} = "rsync" this should |
966 |
|
|
# be a file system path, eg '/' or '/home'. |
967 |
|
|
# |
968 |
|
|
# For $Conf{XferMethod} = "rsyncd" this should be the name of the module |
969 |
|
|
# to backup (ie: the name from /etc/rsynd.conf). |
970 |
|
|
# |
971 |
|
|
# This can also be a list of multiple file system paths or modules. |
972 |
|
|
# For example, by adding --one-file-system to $Conf{RsyncArgs} you |
973 |
|
|
# can backup each file system separately, which makes restoring one |
974 |
|
|
# bad file system easier. In this case you would list all of the mount |
975 |
|
|
# points: |
976 |
|
|
# |
977 |
|
|
# $Conf{RsyncShareName} = ['/', '/var', '/data', '/boot']; |
978 |
|
|
# |
979 |
|
|
$Conf{RsyncShareName} = '/'; |
980 |
|
|
|
981 |
|
|
# |
982 |
|
|
# Rsync daemon port on the client, for $Conf{XferMethod} = "rsyncd". |
983 |
|
|
# |
984 |
|
|
$Conf{RsyncdClientPort} = 873; |
985 |
|
|
|
986 |
|
|
# |
987 |
|
|
# Rsync daemon user name on client, for $Conf{XferMethod} = "rsyncd". |
988 |
|
|
# The user name and password are stored on the client in whatever file |
989 |
|
|
# the "secrets file" parameter in rsyncd.conf points to |
990 |
|
|
# (eg: /etc/rsyncd.secrets). |
991 |
|
|
# |
992 |
|
|
$Conf{RsyncdUserName} = ''; |
993 |
|
|
|
994 |
|
|
# |
995 |
|
|
# Rsync daemon user name on client, for $Conf{XferMethod} = "rsyncd". |
996 |
|
|
# The user name and password are stored on the client in whatever file |
997 |
|
|
# the "secrets file" parameter in rsyncd.conf points to |
998 |
|
|
# (eg: /etc/rsyncd.secrets). |
999 |
|
|
# |
1000 |
|
|
$Conf{RsyncdPasswd} = ''; |
1001 |
|
|
|
1002 |
|
|
# |
1003 |
|
|
# Whether authentication is mandatory when connecting to the client's |
1004 |
|
|
# rsyncd. By default this is on, ensuring that BackupPC will refuse to |
1005 |
|
|
# connect to an rsyncd on the client that is not password protected. |
1006 |
|
|
# Turn off at your own risk. |
1007 |
|
|
# |
1008 |
|
|
$Conf{RsyncdAuthRequired} = 1; |
1009 |
|
|
|
1010 |
|
|
# |
1011 |
|
|
# When rsync checksum caching is enabled (by adding the |
1012 |
|
|
# --checksum-seed=32761 option to $Conf{RsyncArgs}), the cached |
1013 |
|
|
# checksums can be occaisonally verified to make sure the file |
1014 |
|
|
# contents matches the cached checksums. This is to avoid the |
1015 |
|
|
# risk that disk problems might cause the pool file contents to |
1016 |
|
|
# get corrupted, but the cached checksums would make BackupPC |
1017 |
|
|
# think that the file still matches the client. |
1018 |
|
|
# |
1019 |
|
|
# This setting is the probability (0 means never and 1 means always) |
1020 |
|
|
# that a file will be rechecked. Setting it to 0 means the checksums |
1021 |
|
|
# will not be rechecked (unless there is a phase 0 failure). Setting |
1022 |
|
|
# it to 1 (ie: 100%) means all files will be checked, but that is |
1023 |
|
|
# not a desirable setting since you are better off simply turning |
1024 |
|
|
# caching off (ie: remove the --checksum-seed option). |
1025 |
|
|
# |
1026 |
|
|
# The default of 0.01 means 1% (on average) of the files during a full |
1027 |
|
|
# backup will have their cached checksum re-checked. |
1028 |
|
|
# |
1029 |
|
|
# This setting has no effect unless checksum caching is turned on. |
1030 |
|
|
# |
1031 |
|
|
$Conf{RsyncCsumCacheVerifyProb} = 0.01; |
1032 |
|
|
|
1033 |
|
|
# |
1034 |
|
|
# Arguments to rsync for backup. Do not edit the first set unless you |
1035 |
|
|
# have a thorough understanding of how File::RsyncP works. |
1036 |
|
|
# |
1037 |
|
|
# Examples of additional arguments that should work are --exclude/--include, |
1038 |
|
|
# eg: |
1039 |
|
|
# |
1040 |
|
|
# $Conf{RsyncArgs} = [ |
1041 |
|
|
# # original arguments here |
1042 |
|
|
# '-v', |
1043 |
|
|
# '--exclude', '/proc', |
1044 |
|
|
# '--exclude', '*.tmp', |
1045 |
|
|
# ]; |
1046 |
|
|
# |
1047 |
|
|
$Conf{RsyncArgs} = [ |
1048 |
|
|
# |
1049 |
|
|
# Do not edit these! |
1050 |
|
|
# |
1051 |
|
|
'--numeric-ids', |
1052 |
|
|
'--perms', |
1053 |
|
|
'--owner', |
1054 |
|
|
'--group', |
1055 |
|
|
'--devices', |
1056 |
|
|
'--links', |
1057 |
|
|
'--times', |
1058 |
|
|
'--block-size=2048', |
1059 |
|
|
'--recursive', |
1060 |
|
|
|
1061 |
|
|
# |
1062 |
|
|
# If you are using a patched client rsync that supports the |
1063 |
|
|
# --checksum-seed option (see http://backuppc.sourceforge.net), |
1064 |
|
|
# then uncomment this to enabled rsync checksum cachcing |
1065 |
|
|
# |
1066 |
|
|
#'--checksum-seed=32761', |
1067 |
|
|
|
1068 |
|
|
# |
1069 |
|
|
# Add additional arguments here |
1070 |
|
|
# |
1071 |
|
|
]; |
1072 |
|
|
|
1073 |
|
|
# |
1074 |
|
|
# Arguments to rsync for restore. Do not edit the first set unless you |
1075 |
|
|
# have a thorough understanding of how File::RsyncP works. |
1076 |
|
|
# |
1077 |
|
|
# If you want to disable direct restores using rsync (eg: is the module |
1078 |
|
|
# is read-only), you should set $Conf{RsyncRestoreArgs} to undef and |
1079 |
|
|
# the corresponding CGI restore option will be removed. |
1080 |
|
|
# |
1081 |
|
|
$Conf{RsyncRestoreArgs} = [ |
1082 |
|
|
# |
1083 |
|
|
# Do not edit these! |
1084 |
|
|
# |
1085 |
|
|
'--numeric-ids', |
1086 |
|
|
'--perms', |
1087 |
|
|
'--owner', |
1088 |
|
|
'--group', |
1089 |
|
|
'--devices', |
1090 |
|
|
'--links', |
1091 |
|
|
'--times', |
1092 |
|
|
'--block-size=2048', |
1093 |
|
|
'--relative', |
1094 |
|
|
'--ignore-times', |
1095 |
|
|
'--recursive', |
1096 |
|
|
|
1097 |
|
|
# |
1098 |
|
|
# If you are using a patched client rsync that supports the |
1099 |
|
|
# --checksum-seed option (see http://backuppc.sourceforge.net), |
1100 |
|
|
# then uncomment this to enabled rsync checksum cachcing |
1101 |
|
|
# |
1102 |
|
|
#'--checksum-seed=32761', |
1103 |
|
|
|
1104 |
|
|
# |
1105 |
|
|
# Add additional arguments here |
1106 |
|
|
# |
1107 |
|
|
]; |
1108 |
|
|
|
1109 |
|
|
# |
1110 |
|
|
# Archive Destination |
1111 |
|
|
# |
1112 |
|
|
# The Destination of the archive |
1113 |
|
|
# e.g. /tmp for file archive or /dev/nst0 for device archive |
1114 |
|
|
# |
1115 |
|
|
$Conf{ArchiveDest} = '/tmp'; |
1116 |
|
|
|
1117 |
|
|
# |
1118 |
|
|
# Archive Compression type |
1119 |
|
|
# |
1120 |
|
|
# The valid values are: |
1121 |
|
|
# |
1122 |
|
|
# - 'none': No Compression |
1123 |
|
|
# |
1124 |
|
|
# - 'gzip': Medium Compression. Recommended. |
1125 |
|
|
# |
1126 |
|
|
# - 'bzip2': High Compression but takes longer. |
1127 |
|
|
# |
1128 |
|
|
$Conf{ArchiveComp} = 'gzip'; |
1129 |
|
|
|
1130 |
|
|
# |
1131 |
|
|
# Archive Parity Files |
1132 |
|
|
# |
1133 |
|
|
# The amount of Parity data to generate, as a percentage |
1134 |
|
|
# of the archive size. |
1135 |
|
|
# Uses the commandline par2 (par2cmdline) available from |
1136 |
|
|
# http://parchive.sourceforge.net |
1137 |
|
|
# |
1138 |
|
|
# Only useful for file dumps. |
1139 |
|
|
# |
1140 |
|
|
# Set to 0 to disable this feature. |
1141 |
|
|
# |
1142 |
|
|
$Conf{ArchivePar} = 0; |
1143 |
|
|
|
1144 |
|
|
# |
1145 |
|
|
# Archive Size Split |
1146 |
|
|
# |
1147 |
|
|
# Only for file archives. Splits the output into |
1148 |
|
|
# the specified size * 1,000,000. |
1149 |
|
|
# e.g. to split into 650,000,000 bytes, specify 650 below. |
1150 |
|
|
# |
1151 |
|
|
# If the value is 0, or if $Conf{ArchiveDest} is an existing file or |
1152 |
|
|
# device (e.g. a streaming tape drive), this feature is disabled. |
1153 |
|
|
# |
1154 |
|
|
$Conf{ArchiveSplit} = 0; |
1155 |
|
|
|
1156 |
|
|
# |
1157 |
|
|
# Archive Command |
1158 |
|
|
# |
1159 |
|
|
# This is the command that is called to actually run the archive process |
1160 |
|
|
# for each host. The following variables are substituted at run-time: |
1161 |
|
|
# |
1162 |
|
|
# $Installdir The installation directory of BackupPC |
1163 |
|
|
# $tarCreatePath The path to BackupPC_tarCreate |
1164 |
|
|
# $splitpath The path to the split program |
1165 |
|
|
# $parpath The path to the par2 program |
1166 |
|
|
# $host The host to archive |
1167 |
|
|
# $backupnumber The backup number of the host to archive |
1168 |
|
|
# $compression The path to the compression program |
1169 |
|
|
# $compext The extension assigned to the compression type |
1170 |
|
|
# $splitsize The number of bytes to split archives into |
1171 |
|
|
# $archiveloc The location to put the archive |
1172 |
|
|
# $parfile The amount of parity data to create (percentage) |
1173 |
|
|
# |
1174 |
|
|
$Conf{ArchiveClientCmd} = '$Installdir/bin/BackupPC_archiveHost' |
1175 |
|
|
. ' $tarCreatePath $splitpath $parpath $host $backupnumber' |
1176 |
|
|
. ' $compression $compext $splitsize $archiveloc $parfile *'; |
1177 |
|
|
|
1178 |
|
|
# |
1179 |
|
|
# Full path for ssh. Security caution: normal users should not |
1180 |
|
|
# allowed to write to this file or directory. |
1181 |
|
|
# |
1182 |
|
|
$Conf{SshPath} = '/usr/bin/ssh'; |
1183 |
|
|
|
1184 |
|
|
# |
1185 |
|
|
# Full path for nmblookup. Security caution: normal users should not |
1186 |
|
|
# allowed to write to this file or directory. |
1187 |
|
|
# |
1188 |
|
|
# nmblookup is from the Samba distribution. nmblookup is used to get the |
1189 |
|
|
# netbios name, necessary for DHCP hosts. |
1190 |
|
|
# |
1191 |
|
|
$Conf{NmbLookupPath} = '/usr/bin/nmblookup'; |
1192 |
|
|
|
1193 |
|
|
# |
1194 |
|
|
# NmbLookup command. Given an IP address, does an nmblookup on that |
1195 |
|
|
# IP address. The following variables are substituted at run-time: |
1196 |
|
|
# |
1197 |
|
|
# $nmbLookupPath path to nmblookup ($Conf{NmbLookupPath}) |
1198 |
|
|
# $host IP address |
1199 |
|
|
# |
1200 |
|
|
# This command is only used for DHCP hosts: given an IP address, this |
1201 |
|
|
# command should try to find its NetBios name. |
1202 |
|
|
# |
1203 |
|
|
$Conf{NmbLookupCmd} = '$nmbLookupPath -A $host'; |
1204 |
|
|
|
1205 |
|
|
# |
1206 |
|
|
# NmbLookup command. Given a netbios name, finds that host by doing |
1207 |
|
|
# a NetBios lookup. Several variables are substituted at run-time: |
1208 |
|
|
# |
1209 |
|
|
# $nmbLookupPath path to nmblookup ($Conf{NmbLookupPath}) |
1210 |
|
|
# $host NetBios name |
1211 |
|
|
# |
1212 |
|
|
# In some cases you might need to change the broadcast address, for |
1213 |
|
|
# example if nmblookup uses 192.168.255.255 by default and you find |
1214 |
|
|
# that doesn't work, try 192.168.1.255 (or your equivalent class C |
1215 |
|
|
# address) using the -B option: |
1216 |
|
|
# |
1217 |
|
|
# $Conf{NmbLookupFindHostCmd} = '$nmbLookupPath -B 192.168.1.255 $host'; |
1218 |
|
|
# |
1219 |
|
|
# If you use a WINS server and your machines don't respond to |
1220 |
|
|
# multicast NetBios requests you can use this (replace 1.2.3.4 |
1221 |
|
|
# with the IP address of your WINS server): |
1222 |
|
|
# |
1223 |
|
|
# $Conf{NmbLookupFindHostCmd} = '$nmbLookupPath -R -U 1.2.3.4 $host'; |
1224 |
|
|
# |
1225 |
|
|
# This is preferred over multicast since it minimizes network traffic. |
1226 |
|
|
# |
1227 |
|
|
# Experiment manually for your site to see what form of nmblookup command |
1228 |
|
|
# works. |
1229 |
|
|
# |
1230 |
|
|
$Conf{NmbLookupFindHostCmd} = '$nmbLookupPath $host'; |
1231 |
|
|
|
1232 |
|
|
# |
1233 |
|
|
# For fixed IP address hosts, BackupPC_dump can also verify the netbios |
1234 |
|
|
# name to ensure it matches the host name. An error is generated if |
1235 |
|
|
# they do not match. Typically this flag is off. But if you are going |
1236 |
|
|
# to transition a bunch of machines from fixed host addresses to DHCP, |
1237 |
|
|
# setting this flag is a great way to verify that the machines have |
1238 |
|
|
# their netbios name set correctly before turning on DCHP. |
1239 |
|
|
# |
1240 |
|
|
$Conf{FixedIPNetBiosNameCheck} = 0; |
1241 |
|
|
|
1242 |
|
|
# |
1243 |
|
|
# Full path to the ping command. Security caution: normal users |
1244 |
|
|
# should not be allowed to write to this file or directory. |
1245 |
|
|
# |
1246 |
|
|
# If you want to disable ping checking, set this to some program |
1247 |
|
|
# that exits with 0 status, eg: |
1248 |
|
|
# |
1249 |
|
|
# $Conf{PingPath} = '/bin/echo'; |
1250 |
|
|
# |
1251 |
|
|
$Conf{PingPath} = '/bin/ping'; |
1252 |
|
|
|
1253 |
|
|
# |
1254 |
|
|
# Ping command. The following variables are substituted at run-time: |
1255 |
|
|
# |
1256 |
|
|
# $pingPath path to ping ($Conf{PingPath}) |
1257 |
|
|
# $host host name |
1258 |
|
|
# |
1259 |
|
|
# Wade Brown reports that on solaris 2.6 and 2.7 ping -s returns the wrong |
1260 |
|
|
# exit status (0 even on failure). Replace with "ping $host 1", which |
1261 |
|
|
# gets the correct exit status but we don't get the round-trip time. |
1262 |
|
|
# |
1263 |
|
|
$Conf{PingCmd} = '$pingPath -c 1 $host'; |
1264 |
|
|
|
1265 |
|
|
# |
1266 |
|
|
# Path to init.d script and command to use that script to start the |
1267 |
|
|
# server from the CGI interface. The following variables are substituted |
1268 |
|
|
# at run-time: |
1269 |
|
|
# |
1270 |
|
|
# $sshPath path to ssh ($Conf{SshPath}) |
1271 |
|
|
# $serverHost same as $Conf{ServerHost} |
1272 |
|
|
# $serverInitdPath path to init.d script ($Conf{ServerInitdPath}) |
1273 |
|
|
# |
1274 |
|
|
# Example: |
1275 |
|
|
# |
1276 |
|
|
# $Conf{ServerInitdPath} = '/etc/init.d/backuppc'; |
1277 |
|
|
# $Conf{ServerInitdStartCmd} = '$sshPath -q -x -l root $serverHost' |
1278 |
|
|
# . ' $serverInitdPath start' |
1279 |
|
|
# . ' < /dev/null >& /dev/null'; |
1280 |
|
|
# |
1281 |
|
|
$Conf{ServerInitdPath} = ''; |
1282 |
|
|
$Conf{ServerInitdStartCmd} = ''; |
1283 |
|
|
|
1284 |
|
|
# |
1285 |
|
|
# Compression level to use on files. 0 means no compression. Compression |
1286 |
|
|
# levels can be from 1 (least cpu time, slightly worse compression) to |
1287 |
|
|
# 9 (most cpu time, slightly better compression). The recommended value |
1288 |
|
|
# is 3. Changing to 5, for example, will take maybe 20% more cpu time |
1289 |
|
|
# and will get another 2-3% additional compression. See the zlib |
1290 |
|
|
# documentation for more information about compression levels. |
1291 |
|
|
# |
1292 |
|
|
# Changing compression on or off after backups have already been done |
1293 |
|
|
# will require both compressed and uncompressed pool files to be stored. |
1294 |
|
|
# This will increase the pool storage requirements, at least until all |
1295 |
|
|
# the old backups expire and are deleted. |
1296 |
|
|
# |
1297 |
|
|
# It is ok to change the compression value (from one non-zero value to |
1298 |
|
|
# another non-zero value) after dumps are already done. Since BackupPC |
1299 |
|
|
# matches pool files by comparing the uncompressed versions, it will still |
1300 |
|
|
# correctly match new incoming files against existing pool files. The |
1301 |
|
|
# new compression level will take effect only for new files that are |
1302 |
|
|
# newly compressed and added to the pool. |
1303 |
|
|
# |
1304 |
|
|
# If compression was off and you are enabling compression for the first |
1305 |
|
|
# time you can use the BackupPC_compressPool utility to compress the |
1306 |
|
|
# pool. This avoids having the pool grow to accommodate both compressed |
1307 |
|
|
# and uncompressed backups. See the documentation for more information. |
1308 |
|
|
# |
1309 |
|
|
# Note: compression needs the Compress::Zlib perl library. If the |
1310 |
|
|
# Compress::Zlib library can't be found then $Conf{CompressLevel} is |
1311 |
|
|
# forced to 0 (compression off). |
1312 |
|
|
# |
1313 |
|
|
$Conf{CompressLevel} = 0; |
1314 |
|
|
|
1315 |
|
|
# |
1316 |
|
|
# Maximum round-trip ping time in milliseconds. This threshold is set |
1317 |
|
|
# to avoid backing up PCs that are remotely connected through WAN or |
1318 |
|
|
# dialup connections. The output from ping -s (assuming it is supported |
1319 |
|
|
# on your system) is used to check the round-trip packet time. On your |
1320 |
|
|
# local LAN round-trip times should be much less than 20msec. On most |
1321 |
|
|
# WAN or dialup connections the round-trip time will be typically more |
1322 |
|
|
# than 20msec. Tune if necessary. |
1323 |
|
|
# |
1324 |
|
|
$Conf{PingMaxMsec} = 20; |
1325 |
|
|
|
1326 |
|
|
# |
1327 |
|
|
# Timeout in seconds when listening for the transport program's |
1328 |
|
|
# (smbclient, tar etc) stdout. If no output is received during this |
1329 |
|
|
# time, then it is assumed that something has wedged during a backup, |
1330 |
|
|
# and the backup is terminated. |
1331 |
|
|
# |
1332 |
|
|
# Note that stdout buffering combined with huge files being backed up |
1333 |
|
|
# could cause longish delays in the output from smbclient that |
1334 |
|
|
# BackupPC_dump sees, so in rare cases you might want to increase |
1335 |
|
|
# this value. |
1336 |
|
|
# |
1337 |
|
|
# Despite the name, this parameter sets the timeout for all transport |
1338 |
|
|
# methods (tar, smb etc). |
1339 |
|
|
# |
1340 |
dpavlin |
316 |
$Conf{ClientTimeout} = 72000; |
1341 |
dpavlin |
1 |
|
1342 |
|
|
# |
1343 |
|
|
# Maximum number of log files we keep around in each PC's directory |
1344 |
|
|
# (ie: pc/$host). These files are aged monthly. A setting of 12 |
1345 |
|
|
# means there will be at most the files LOG, LOG.0, LOG.1, ... LOG.11 |
1346 |
|
|
# in the pc/$host directory (ie: about a years worth). (Except this |
1347 |
|
|
# month's LOG, these files will have a .z extension if compression |
1348 |
|
|
# is on). |
1349 |
|
|
# |
1350 |
|
|
# If you decrease this number after BackupPC has been running for a |
1351 |
|
|
# while you will have to manually remove the older log files. |
1352 |
|
|
# |
1353 |
|
|
$Conf{MaxOldPerPCLogFiles} = 12; |
1354 |
|
|
|
1355 |
|
|
# |
1356 |
|
|
# Optional commands to run before and after dumps and restores. |
1357 |
|
|
# Stdout from these commands will be written to the Xfer (or Restore) |
1358 |
|
|
# log file. One example of using these commands would be to |
1359 |
|
|
# shut down and restart a database server, or to dump a database |
1360 |
|
|
# to files for backup. Example: |
1361 |
|
|
# |
1362 |
|
|
# $Conf{DumpPreUserCmd} = '$sshPath -q -x -l root $host /usr/bin/dumpMysql'; |
1363 |
|
|
# |
1364 |
|
|
# The following variable substitutions are made at run time for |
1365 |
|
|
# $Conf{DumpPreUserCmd} and $Conf{DumpPostUserCmd}: |
1366 |
|
|
# |
1367 |
|
|
# $type type of dump (incr or full) |
1368 |
|
|
# $xferOK 1 if the dump succeeded, 0 if it didn't |
1369 |
|
|
# $client client name being backed up |
1370 |
|
|
# $host host name (could be different from client name if |
1371 |
|
|
# $Conf{ClientNameAlias} is set) |
1372 |
|
|
# $hostIP IP address of host |
1373 |
|
|
# $user user name from the hosts file |
1374 |
|
|
# $moreUsers list of additional users from the hosts file |
1375 |
|
|
# $share the first share name |
1376 |
|
|
# $shares list of all the share names |
1377 |
|
|
# $XferMethod value of $Conf{XferMethod} (eg: tar, rsync, smb) |
1378 |
|
|
# $sshPath value of $Conf{SshPath}, |
1379 |
|
|
# $cmdType set to DumpPreUserCmd or DumpPostUserCmd |
1380 |
|
|
# |
1381 |
|
|
# The following variable substitutions are made at run time for |
1382 |
|
|
# $Conf{RestorePreUserCmd} and $Conf{RestorePostUserCmd}: |
1383 |
|
|
# |
1384 |
|
|
# $client client name being backed up |
1385 |
|
|
# $xferOK 1 if the restore succeeded, 0 if it didn't |
1386 |
|
|
# $host host name (could be different from client name if |
1387 |
|
|
# $Conf{ClientNameAlias} is set) |
1388 |
|
|
# $hostIP IP address of host |
1389 |
|
|
# $user user name from the hosts file |
1390 |
|
|
# $moreUsers list of additional users from the hosts file |
1391 |
|
|
# $share the first share name |
1392 |
|
|
# $XferMethod value of $Conf{XferMethod} (eg: tar, rsync, smb) |
1393 |
|
|
# $sshPath value of $Conf{SshPath}, |
1394 |
|
|
# $type set to "restore" |
1395 |
|
|
# $bkupSrcHost host name of the restore source |
1396 |
|
|
# $bkupSrcShare share name of the restore source |
1397 |
|
|
# $bkupSrcNum backup number of the restore source |
1398 |
|
|
# $pathHdrSrc common starting path of restore source |
1399 |
|
|
# $pathHdrDest common starting path of destination |
1400 |
|
|
# $fileList list of files being restored |
1401 |
|
|
# $cmdType set to RestorePreUserCmd or RestorePostUserCmd |
1402 |
|
|
# |
1403 |
|
|
# The following variable substitutions are made at run time for |
1404 |
|
|
# $Conf{ArchivePreUserCmd} and $Conf{ArchivePostUserCmd}: |
1405 |
|
|
# |
1406 |
|
|
# $client client name being backed up |
1407 |
|
|
# $xferOK 1 if the archive succeeded, 0 if it didn't |
1408 |
|
|
# $host Name of the archive host |
1409 |
|
|
# $user user name from the hosts file |
1410 |
|
|
# $share the first share name |
1411 |
|
|
# $XferMethod value of $Conf{XferMethod} (eg: tar, rsync, smb) |
1412 |
|
|
# $HostList list of hosts being archived |
1413 |
|
|
# $BackupList list of backup numbers for the hosts being archived |
1414 |
|
|
# $archiveloc location where the archive is sent to |
1415 |
|
|
# $parfile amount of parity data being generated (percentage) |
1416 |
|
|
# $compression compression program being used (eg: cat, gzip, bzip2) |
1417 |
|
|
# $compext extension used for compression type (eg: raw, gz, bz2) |
1418 |
|
|
# $splitsize size of the files that the archive creates |
1419 |
|
|
# $sshPath value of $Conf{SshPath}, |
1420 |
|
|
# $type set to "archive" |
1421 |
|
|
# $cmdType set to ArchivePreUserCmd or ArchivePostUserCmd |
1422 |
|
|
# |
1423 |
|
|
$Conf{DumpPreUserCmd} = undef; |
1424 |
|
|
$Conf{DumpPostUserCmd} = undef; |
1425 |
|
|
$Conf{RestorePreUserCmd} = undef; |
1426 |
|
|
$Conf{RestorePostUserCmd} = undef; |
1427 |
|
|
$Conf{ArchivePreUserCmd} = undef; |
1428 |
|
|
$Conf{ArchivePostUserCmd} = undef; |
1429 |
|
|
|
1430 |
|
|
# |
1431 |
|
|
# Override the client's host name. This allows multiple clients |
1432 |
|
|
# to all refer to the same physical host. This should only be |
1433 |
|
|
# set in the per-PC config file and is only used by BackupPC at |
1434 |
|
|
# the last moment prior to generating the command used to backup |
1435 |
|
|
# that machine (ie: the value of $Conf{ClientNameAlias} is invisible |
1436 |
|
|
# everywhere else in BackupPC). The setting can be a host name or |
1437 |
|
|
# IP address, eg: |
1438 |
|
|
# |
1439 |
|
|
# $Conf{ClientNameAlias} = 'realHostName'; |
1440 |
|
|
# $Conf{ClientNameAlias} = '192.1.1.15'; |
1441 |
|
|
# |
1442 |
|
|
# will cause the relevant smb/tar/rsync backup/restore commands to be |
1443 |
|
|
# directed to realHostName, not the client name. |
1444 |
|
|
# |
1445 |
|
|
# Note: this setting doesn't work for hosts with DHCP set to 1. |
1446 |
|
|
# |
1447 |
|
|
$Conf{ClientNameAlias} = undef; |
1448 |
|
|
|
1449 |
|
|
# |
1450 |
|
|
# Advanced option for asking BackupPC to load additional perl modules. |
1451 |
|
|
# Can be a list (array ref) of module names to load at startup. |
1452 |
|
|
# |
1453 |
|
|
$Conf{PerlModuleLoad} = undef; |
1454 |
|
|
|
1455 |
|
|
########################################################################### |
1456 |
|
|
# Email reminders, status and messages |
1457 |
|
|
# (can be overridden in the per-PC config.pl) |
1458 |
|
|
########################################################################### |
1459 |
|
|
# |
1460 |
|
|
# Full path to the sendmail command. Security caution: normal users |
1461 |
|
|
# should not allowed to write to this file or directory. |
1462 |
|
|
# |
1463 |
|
|
$Conf{SendmailPath} = '/usr/sbin/sendmail'; |
1464 |
|
|
|
1465 |
|
|
# |
1466 |
|
|
# Minimum period between consecutive emails to a single user. |
1467 |
|
|
# This tries to keep annoying email to users to a reasonable |
1468 |
|
|
# level. Email checks are done nightly, so this number is effectively |
1469 |
|
|
# rounded up (ie: 2.5 means a user will never receive email more |
1470 |
|
|
# than once every 3 days). |
1471 |
|
|
# |
1472 |
|
|
$Conf{EMailNotifyMinDays} = 2.5; |
1473 |
|
|
|
1474 |
|
|
# |
1475 |
|
|
# Name to use as the "from" name for email. Depending upon your mail |
1476 |
|
|
# handler this is either a plain name (eg: "admin") or a fully-qualified |
1477 |
|
|
# name (eg: "admin@mydomain.com"). |
1478 |
|
|
# |
1479 |
|
|
$Conf{EMailFromUserName} = ''; |
1480 |
|
|
|
1481 |
|
|
# |
1482 |
|
|
# Destination address to an administrative user who will receive a |
1483 |
|
|
# nightly email with warnings and errors. If there are no warnings |
1484 |
|
|
# or errors then no email will be sent. Depending upon your mail |
1485 |
|
|
# handler this is either a plain name (eg: "admin") or a fully-qualified |
1486 |
|
|
# name (eg: "admin@mydomain.com"). |
1487 |
|
|
# |
1488 |
|
|
$Conf{EMailAdminUserName} = ''; |
1489 |
|
|
|
1490 |
|
|
# |
1491 |
|
|
# Destination domain name for email sent to users. By default |
1492 |
|
|
# this is empty, meaning email is sent to plain, unqualified |
1493 |
|
|
# addresses. Otherwise, set it to the destintation domain, eg: |
1494 |
|
|
# |
1495 |
|
|
# $Cong{EMailUserDestDomain} = '@mydomain.com'; |
1496 |
|
|
# |
1497 |
|
|
# With this setting user email will be set to 'user@mydomain.com'. |
1498 |
|
|
# |
1499 |
|
|
$Conf{EMailUserDestDomain} = ''; |
1500 |
|
|
|
1501 |
|
|
# |
1502 |
|
|
# This subject and message is sent to a user if their PC has never been |
1503 |
|
|
# backed up. |
1504 |
|
|
# |
1505 |
|
|
# These values are language-dependent. The default versions can be |
1506 |
|
|
# found in the language file (eg: lib/BackupPC/Lang/en.pm). If you |
1507 |
|
|
# need to change the message, copy it here and edit it, eg: |
1508 |
|
|
# |
1509 |
|
|
# $Conf{EMailNoBackupEverMesg} = <<'EOF'; |
1510 |
|
|
# To: $user$domain |
1511 |
|
|
# cc: |
1512 |
|
|
# Subject: $subj |
1513 |
dpavlin |
316 |
# $headers |
1514 |
dpavlin |
1 |
# Dear $userName, |
1515 |
|
|
# |
1516 |
|
|
# This is a site-specific email message. |
1517 |
|
|
# EOF |
1518 |
|
|
# |
1519 |
|
|
$Conf{EMailNoBackupEverSubj} = undef; |
1520 |
|
|
$Conf{EMailNoBackupEverMesg} = undef; |
1521 |
|
|
|
1522 |
|
|
# |
1523 |
|
|
# How old the most recent backup has to be before notifying user. |
1524 |
|
|
# When there have been no backups in this number of days the user |
1525 |
|
|
# is sent an email. |
1526 |
|
|
# |
1527 |
|
|
$Conf{EMailNotifyOldBackupDays} = 7.0; |
1528 |
|
|
|
1529 |
|
|
# |
1530 |
|
|
# This subject and message is sent to a user if their PC has not recently |
1531 |
|
|
# been backed up (ie: more than $Conf{EMailNotifyOldBackupDays} days ago). |
1532 |
|
|
# |
1533 |
|
|
# These values are language-dependent. The default versions can be |
1534 |
|
|
# found in the language file (eg: lib/BackupPC/Lang/en.pm). If you |
1535 |
|
|
# need to change the message, copy it here and edit it, eg: |
1536 |
|
|
# |
1537 |
|
|
# $Conf{EMailNoBackupRecentMesg} = <<'EOF'; |
1538 |
|
|
# To: $user$domain |
1539 |
|
|
# cc: |
1540 |
|
|
# Subject: $subj |
1541 |
dpavlin |
316 |
# $headers |
1542 |
dpavlin |
1 |
# Dear $userName, |
1543 |
|
|
# |
1544 |
|
|
# This is a site-specific email message. |
1545 |
|
|
# EOF |
1546 |
|
|
# |
1547 |
|
|
$Conf{EMailNoBackupRecentSubj} = undef; |
1548 |
|
|
$Conf{EMailNoBackupRecentMesg} = undef; |
1549 |
|
|
|
1550 |
|
|
# |
1551 |
|
|
# How old the most recent backup of Outlook files has to be before |
1552 |
|
|
# notifying user. |
1553 |
|
|
# |
1554 |
|
|
$Conf{EMailNotifyOldOutlookDays} = 5.0; |
1555 |
|
|
|
1556 |
|
|
# |
1557 |
|
|
# This subject and message is sent to a user if their Outlook files have |
1558 |
|
|
# not recently been backed up (ie: more than $Conf{EMailNotifyOldOutlookDays} |
1559 |
|
|
# days ago). |
1560 |
|
|
# |
1561 |
|
|
# These values are language-dependent. The default versions can be |
1562 |
|
|
# found in the language file (eg: lib/BackupPC/Lang/en.pm). If you |
1563 |
|
|
# need to change the message, copy it here and edit it, eg: |
1564 |
|
|
# |
1565 |
|
|
# $Conf{EMailOutlookBackupMesg} = <<'EOF'; |
1566 |
|
|
# To: $user$domain |
1567 |
|
|
# cc: |
1568 |
|
|
# Subject: $subj |
1569 |
dpavlin |
316 |
# $headers |
1570 |
dpavlin |
1 |
# Dear $userName, |
1571 |
|
|
# |
1572 |
|
|
# This is a site-specific email message. |
1573 |
|
|
# EOF |
1574 |
|
|
# |
1575 |
|
|
$Conf{EMailOutlookBackupSubj} = undef; |
1576 |
|
|
$Conf{EMailOutlookBackupMesg} = undef; |
1577 |
|
|
|
1578 |
|
|
########################################################################### |
1579 |
|
|
# CGI user interface configuration settings |
1580 |
|
|
# (can be overridden in the per-PC config.pl) |
1581 |
|
|
########################################################################### |
1582 |
|
|
# |
1583 |
|
|
# Normal users can only access information specific to their host. |
1584 |
|
|
# They can start/stop/browse/restore backups. |
1585 |
|
|
# |
1586 |
|
|
# Administrative users have full access to all hosts, plus overall |
1587 |
|
|
# status and log information. |
1588 |
|
|
# |
1589 |
|
|
# The administrative users are the union of the unix/linux group |
1590 |
|
|
# $Conf{CgiAdminUserGroup} and the manual list of users, separated |
1591 |
|
|
# by spaces, in $Conf{CgiAdminUsers}. If you don't want a group or |
1592 |
|
|
# manual list of users set the corresponding configuration setting |
1593 |
|
|
# to undef or an empty string. |
1594 |
|
|
# |
1595 |
|
|
# If you want every user to have admin privileges (careful!), set |
1596 |
|
|
# $Conf{CgiAdminUsers} = '*'. |
1597 |
|
|
# |
1598 |
|
|
# Examples: |
1599 |
|
|
# $Conf{CgiAdminUserGroup} = 'admin'; |
1600 |
|
|
# $Conf{CgiAdminUsers} = 'craig celia'; |
1601 |
|
|
# --> administrative users are the union of group admin, plus |
1602 |
|
|
# craig and celia. |
1603 |
|
|
# |
1604 |
|
|
# $Conf{CgiAdminUserGroup} = ''; |
1605 |
|
|
# $Conf{CgiAdminUsers} = 'craig celia'; |
1606 |
|
|
# --> administrative users are only craig and celia'. |
1607 |
|
|
# |
1608 |
|
|
$Conf{CgiAdminUserGroup} = ''; |
1609 |
|
|
$Conf{CgiAdminUsers} = ''; |
1610 |
|
|
|
1611 |
|
|
# |
1612 |
|
|
# URL of the BackupPC_Admin CGI script. Used for email messages. |
1613 |
|
|
# |
1614 |
|
|
$Conf{CgiURL} = undef; |
1615 |
|
|
|
1616 |
|
|
# |
1617 |
|
|
# Language to use. See lib/BackupPC/Lang for the list of supported |
1618 |
|
|
# languages, which include English (en), French (fr), Spanish (es), |
1619 |
|
|
# German (de), Italian (it) and Dutch (nl). |
1620 |
|
|
# |
1621 |
|
|
# Currently the Language setting applies to the CGI interface and email |
1622 |
|
|
# messages sent to users. Log files and other text are still in English. |
1623 |
|
|
# |
1624 |
|
|
$Conf{Language} = 'en'; |
1625 |
|
|
|
1626 |
|
|
# |
1627 |
|
|
# User names that are rendered by the CGI interface can be turned |
1628 |
|
|
# into links into their home page or other information about the |
1629 |
|
|
# user. To set this up you need to create two sprintf() strings, |
1630 |
|
|
# that each contain a single '%s' that will be replaced by the user |
1631 |
|
|
# name. The default is a mailto: link. |
1632 |
|
|
# |
1633 |
|
|
# $Conf{CgiUserHomePageCheck} should be an absolute file path that |
1634 |
|
|
# is used to check (via "-f") that the user has a valid home page. |
1635 |
|
|
# Set this to undef or an empty string to turn off this check. |
1636 |
|
|
# |
1637 |
|
|
# $Conf{CgiUserUrlCreate} should be a full URL that points to the |
1638 |
|
|
# user's home page. Set this to undef or an empty string to turn |
1639 |
|
|
# off generation of URLs for user names. |
1640 |
|
|
# |
1641 |
|
|
# Example: |
1642 |
|
|
# $Conf{CgiUserHomePageCheck} = '/var/www/html/users/%s.html'; |
1643 |
|
|
# $Conf{CgiUserUrlCreate} = 'http://myhost/users/%s.html'; |
1644 |
|
|
# --> if /var/www/html/users/craig.html exists, then 'craig' will |
1645 |
|
|
# be rendered as a link to http://myhost/users/craig.html. |
1646 |
|
|
# |
1647 |
|
|
$Conf{CgiUserHomePageCheck} = ''; |
1648 |
|
|
$Conf{CgiUserUrlCreate} = 'mailto:%s'; |
1649 |
|
|
|
1650 |
|
|
# |
1651 |
|
|
# Date display format for CGI interface. True for US-style dates (MM/DD) |
1652 |
|
|
# and zero for international dates (DD/MM). |
1653 |
|
|
# |
1654 |
|
|
$Conf{CgiDateFormatMMDD} = 1; |
1655 |
|
|
|
1656 |
|
|
# |
1657 |
|
|
# If set, the complete list of hosts appears in the left navigation |
1658 |
|
|
# bar pull-down for administrators. Otherwise, just the hosts for which |
1659 |
|
|
# the user is listed in the host file (as either the user or in moreUsers) |
1660 |
|
|
# are displayed. |
1661 |
|
|
# |
1662 |
|
|
$Conf{CgiNavBarAdminAllHosts} = 1; |
1663 |
|
|
|
1664 |
|
|
# |
1665 |
|
|
# Enable/disable the search box in the navigation bar. |
1666 |
|
|
# |
1667 |
|
|
$Conf{CgiSearchBoxEnable} = 1; |
1668 |
|
|
|
1669 |
|
|
# |
1670 |
|
|
# Additional navigation bar links. These appear for both regular users |
1671 |
|
|
# and administrators. This is a list of hashes giving the link (URL) |
1672 |
|
|
# and the text (name) for the link. Specifying lname instead of name |
1673 |
|
|
# uses the language specific string (ie: $Lang->{lname}) instead of |
1674 |
|
|
# just literally displaying name. |
1675 |
|
|
# |
1676 |
|
|
$Conf{CgiNavBarLinks} = [ |
1677 |
|
|
{ |
1678 |
|
|
link => "?action=view&type=docs", |
1679 |
|
|
lname => "Documentation", # actually displays $Lang->{Documentation} |
1680 |
|
|
}, |
1681 |
|
|
{ |
1682 |
|
|
link => "http://backuppc.sourceforge.net/faq", |
1683 |
|
|
name => "FAQ", # displays literal "FAQ" |
1684 |
|
|
}, |
1685 |
|
|
{ |
1686 |
|
|
link => "http://backuppc.sourceforge.net", |
1687 |
|
|
name => "SourceForge", # displays literal "SourceForge" |
1688 |
|
|
}, |
1689 |
|
|
]; |
1690 |
|
|
|
1691 |
|
|
# |
1692 |
|
|
# Hilight colors based on status that are used in the PC summary page. |
1693 |
|
|
# |
1694 |
|
|
$Conf{CgiStatusHilightColor} = { |
1695 |
|
|
Reason_backup_failed => '#ffcccc', |
1696 |
|
|
Reason_backup_done => '#ccffcc', |
1697 |
|
|
Reason_no_ping => '#ffff99', |
1698 |
|
|
Reason_backup_canceled_by_user => '#ff9900', |
1699 |
|
|
Status_backup_in_progress => '#66cc99', |
1700 |
|
|
}; |
1701 |
|
|
|
1702 |
|
|
# |
1703 |
|
|
# Additional CGI header text. |
1704 |
|
|
# |
1705 |
|
|
$Conf{CgiHeaders} = '<meta http-equiv="pragma" content="no-cache">'; |
1706 |
|
|
|
1707 |
|
|
# |
1708 |
|
|
# Directory where images are stored. This directory should be below |
1709 |
|
|
# Apache's DocumentRoot. This value isn't used by BackupPC but is |
1710 |
|
|
# used by configure.pl when you upgrade BackupPC. |
1711 |
|
|
# |
1712 |
|
|
# Example: |
1713 |
|
|
# $Conf{CgiImageDir} = '/usr/local/apache/htdocs/BackupPC'; |
1714 |
|
|
# |
1715 |
|
|
$Conf{CgiImageDir} = ''; |
1716 |
|
|
|
1717 |
|
|
# |
1718 |
|
|
# Additional mappings of file name extenions to Content-Type for |
1719 |
|
|
# individual file restore. See $Ext2ContentType in BackupPC_Admin |
1720 |
|
|
# for the default setting. You can add additional settings here, |
1721 |
|
|
# or override any default settings. Example: |
1722 |
|
|
# |
1723 |
|
|
# $Conf{CgiExt2ContentType} = { |
1724 |
|
|
# 'pl' => 'text/plain', |
1725 |
|
|
# }; |
1726 |
|
|
# |
1727 |
|
|
$Conf{CgiExt2ContentType} = { }; |
1728 |
|
|
|
1729 |
|
|
# |
1730 |
|
|
# URL (without the leading http://host) for BackupPC's image directory. |
1731 |
|
|
# The CGI script uses this value to serve up image files. |
1732 |
|
|
# |
1733 |
|
|
# Example: |
1734 |
|
|
# $Conf{CgiImageDirURL} = '/BackupPC'; |
1735 |
|
|
# |
1736 |
|
|
$Conf{CgiImageDirURL} = ''; |
1737 |
|
|
|
1738 |
|
|
# |
1739 |
|
|
# CSS stylesheet for the CGI interface. It is stored in the |
1740 |
|
|
# $Conf{CgiImageDir} directory and accessed via the |
1741 |
|
|
# $Conf{CgiImageDirURL} URL. |
1742 |
|
|
# |
1743 |
|
|
$Conf{CgiCSSFile} = 'BackupPC_stnd.css'; |
1744 |
dpavlin |
6 |
|
1745 |
|
|
# |
1746 |
dpavlin |
51 |
# add search database dsn |
1747 |
dpavlin |
6 |
# |
1748 |
dpavlin |
51 |
#$Conf{SearchDSN} = 'dbi:SQLite:dbname=$TopDir/search.db'; |
1749 |
|
|
$Conf{SearchDSN} = 'dbi:Pg:dbname=backuppc'; |
1750 |
|
|
$Conf{SearchUser} = 'dpavlin'; |
1751 |
dpavlin |
82 |
# |
1752 |
dpavlin |
303 |
# if you want to use experimental Hyper Estraier support (which require |
1753 |
|
|
# installation of Search::Estraier perl module from CPAN) select |
1754 |
dpavlin |
116 |
# path to index (relative to $TopDir) or node URI |
1755 |
dpavlin |
327 |
# use following line to disable Hyper Estraier and prevent upgrades |
1756 |
|
|
# from overwriting it |
1757 |
|
|
#$Conf{HyperEstraierIndex} = ''; |
1758 |
iklaric |
384 |
$Conf{HyperEstraierIndex} = '___ESTRAIER_URI___'; |
1759 |
dpavlin |
51 |
|
1760 |
dpavlin |
109 |
# |
1761 |
|
|
# temp directory for storing gzip and iso files when createing iso images |
1762 |
|
|
# |
1763 |
|
|
$Conf{GzipTempDir} = 'temp'; |
1764 |
iklaric |
144 |
|
1765 |
|
|
# |
1766 |
dpavlin |
234 |
# nameing schema for snapshots (.tar.gz will be added) |
1767 |
|
|
# \h - hostname |
1768 |
|
|
# \s - share |
1769 |
|
|
# \n - increment numer |
1770 |
iklaric |
144 |
# |
1771 |
dpavlin |
234 |
$Conf{GzipSchema} = '\h_\s_\n'; |
1772 |
|
|
# |
1773 |
iklaric |
144 |
|
1774 |
|
|
# |
1775 |
dpavlin |
260 |
# archive media size (in bytes) |
1776 |
dpavlin |
230 |
# default: 4.2Gb for DVD |
1777 |
iklaric |
144 |
# |
1778 |
dpavlin |
260 |
$Conf{MaxArchiveSize} = 4200 * 1024 * 1024; |
1779 |
dpavlin |
174 |
|
1780 |
|
|
# |
1781 |
dpavlin |
260 |
# maximum size of one (uncompressed) file on archive medium (in bytes) |
1782 |
dpavlin |
234 |
# default: 2Gb - 2k for DVD |
1783 |
dpavlin |
260 |
$Conf{MaxArchiveFileSize} = (2048 - 2) * 1024 * 1024; |
1784 |
dpavlin |
230 |
|
1785 |
|
|
# |
1786 |
dpavlin |
174 |
# Temporary directory for ISO images (relative to install dir) |
1787 |
|
|
# |
1788 |
|
|
$Conf{ISOTempDir} = 'temp/iso'; |
1789 |
|
|
|
1790 |
dpavlin |
202 |
#### |
1791 |
|
|
# configuration data for burning |
1792 |
|
|
#### |
1793 |
|
|
$Conf{CDRecordBin} = 'cdrecord'; |
1794 |
|
|
$Conf{CDRecordOpts} = 'dev=/dev/hdc blank=fast -dao -v -eject -dummy'; |
1795 |
|
|
|
1796 |
|
|
#$Conf{CDRecordBin} = 'dvdrecord'; |
1797 |
|
|
#$Conf{CDRecordOpts} = 'dev=0,0,0 -dao -v -eject -dummy'; |
1798 |
|
|
|
1799 |
|
|
# gzip level for creating tar.gz increments |
1800 |
|
|
# default is -6, -1 is fast, -9 is slow |
1801 |
|
|
#$Conf{GzipLevel} = '-6'; |
1802 |
|
|
$Conf{GzipLevel} = '-1'; |
1803 |
|
|
|
1804 |
|
|
# number of archive copies to burn |
1805 |
|
|
$Conf{BurnMultipleCopies} = 2; |
1806 |
|
|
|
1807 |
dpavlin |
206 |
# Other command-line utilities used |
1808 |
|
|
$Conf{ejectBin} = 'eject'; |
1809 |
|
|
$Conf{ejectOpts} = '/dev/cdrom'; |
1810 |
|
|
|
1811 |
|
|
$Conf{mkisofsBin} = 'mkisofs'; |
1812 |
dpavlin |
355 |
|
1813 |
|
|
# temporary path used when recovering of increments |
1814 |
|
|
# (you might put this into tmpfs if you have enough RAM) |
1815 |
|
|
$Conf{IncrementTempDir} = '/tmp/increment-restore/'; |